Public tenders for locker in United Kingdom

Find all Furniture tenders in the world.
Finding business opportunities has never been easier.

Results for furniture. Make a new search!
FurniturelockerUnited Kingdom

Barry Fire Station Co-Location Works

South Wales Fire and Rescue Service | Published November 15, 2017
Winner
Office Visions (Wales) Ltd
cpvs

South Wales Fire and Rescue Service are looking to appoint a contractor to carry out works to accommodate a co-location facility at Barry Fire Station. Concept design plans have been produced and will include the following work; o Complete strip out of first floor including all M&E. o Fit out to the first floor to the new layout indicated. o Upgrade of external fabric to the main elevations to enhance finishes and appearance. o Minor extension to the rear of the appliance bay to include a new store. This being a load bearing masonry solution with heating, power, lighting and slab / foundation design. o Structural alternations to ensure existing waffle type slab remains in tack and roof supported. Structural works to also review the existing side walls at first floor with the potential for new wind posts as required. o New M&E installation including upgrade to access control and fire alarm system. o New fire escape stair o Drainage alterations internally to take new showers and WC’s at first floor and amended washrooms and kitchen at ground floor. o New finishes throughout first floor and areas where alteration will occur at ground floor, namely kitchen / mess, offices, WC’s, showers, locker rooms, muster and drying room. o New sliding folding partition at first floor including structural support. o Upgrade or new windows / doors as required. o New sanitary ware and FFE as indicated. o New lift installation including M&E and structural alterations. o Alteration of wall locations at ground floor that may prove to have load bearing properties. o External works as indicated to ensure maximisation of parking and altered access / egress proposal by re-aligning internal levels and kerbs to create a one way deployment route. o Re-surfacing works externally. o Allowance for provision of a new covered steel structure at the rear of the service yard. o Upgrades to external lighting. o Review of existing M&E loadings and recommendation for any upgrade works. Outline existing and proposed sketch plans are attached for reference. A design team has recently been appointed to carry out a fully coordinated detailed design and set of Employers Requirements for the purpose of the ITT stages. The team is as follows: Lawray Architects - Lead Consultant, Architect, Principle Designer and Contract Administrator Bingham Hall Partnership - Structural and Civil Engineers DRAC Consulting - Mechanical and Electrical Consultants TC Consult - Cost Consultant The client team consists of Estates representatives from both South Wales Fire and Rescue Service and Welsh Ambulance Service NHS Trust.

Ward and Residential Furniture

NHS Supply Chain acting as agent for NHS Business Services Authority | Published March 21, 2017  -  Deadline April 18, 2017
cpvs
39100000, 39110000, 39112000, 39112100, 39113000, 39113100, 39113200, 39113600, 39113700, 39114000, 39120000, 39121200, 39122000, 39143000, 39143100, 39143113, 39143123, 33196100, 33196200

NHS Supply Chain seeks to establish a non-exclusive Framework Agreement for supply to NHS Supply Chain customer base via the Direct Route.

The scope of the framework is to cover all Ward and Residential Furniture used within but not limited to the following environments:

— Wards;

— Waiting Areas;

— Out Patients;

— Family Areas;

— Dining Areas;

— Lounge Areas;

— Reception Areas;

— Overnight Stay.

This Framework Agreement is for 24 months with the option to extend in incremental stages for up to a total period of 48 months.

There are a total of 20 product lines within the basket which are set out in the ‘Lot Line Detail’ tab and are detailed below:

Patient High Backed Chair; Visitor Stacking Chair; Bariatric Armchair; Bedside Locker; Overbed/Overchair Table; 1 Seater Settee; 2 Seater Settee; 3 Seater Settee; Wardrobe; Chest of Drawers; Dressing Table; Bedside Cabinet; Low Back Easy Chair; Stacking Chair; Dining Chair; Manual Reclining Chair; Electric Reclining Chair; Coffee Table; Dining Table and Beam Seating.

Applicants must be able to provide at least 13 of 20 lines within the basket. If Applicants are unable to meet this requirement then NHS Supply Chain reserves the right to exclude the Applicant from the procurement process and not to consider the tender response for this Framework Agreement any further.

NHS Supply Chain anticipates awarding all Applicants who meet the minimum requirements which are set out in these tender documents and whose Average Basket Score (based on the methodology and definition as stated within Sections 8.3 — 8.5 of this document) meets or exceeds a hurdle of at least 55 % (when rounded up or down from four decimal places (as the case may be) to the nearest whole number) at tender evaluation stage will be awarded all of the product lines submitted for evaluation and should these Applicants be able over the lifetime of the Framework Agreement to supply any of the other product lines in the Basket such Applicants will be given the opportunity to do so.

Please note that Applicants must submit a bid against all evaluated product lines which they intend to supply under the Framework Agreement. If pricing has not been submitted for a particular product line and an applicant is able to supply that particular product line at the time of the Tender submission then NHS Supply Chain reserves the right to not allow the applicant (if successful) to supply that particular product line over the lifetime of the Framework Agreement.

NHS Supply Chain has taken the decision not to sub-divide this Framework Agreement into Lots on the basis that the range of products would be suitable for a basket of goods as the products are broadly similar and the total value would be more attractive to the supply base.

M & E Engineering Design Services at West Road Extra Care Scheme

Corporate Procurement | Published November 30, 2016  -  Deadline December 16, 2016
cpvs
71310000, 71311000, 71318000, 71315200, 71315210, 71530000, 79415200

M & E Engineering Design Services at West Road Extra Care Scheme

The Council is looking to appoint a consultant to provide Mechanical & Electrical Engineering Design Services in accordance with the ACE Schedule of Services – Part G(b) Mechanical and electrical engineering (detailed design in buildings) Single Consultant or non-lead Consultant For use with ACE Agreement 1 – Design for an extra care facility in West Road, West Bromwich, West Midlands. The proposed accommodation would provide as a minimum the following:

• 60 one bedroom and 30 two bed room flats,
• Guest suite with en-suite bathroom,
• Combined lounge, dining and activities room, and kitchenette,
• Communal areas comprising
o Main lounge,
o Dining area,
o Residents tea kitchen,
o Communal wc’s,
o Assisted bathrooms, and
o Hairdressing & beauty therapy,
o Informal seating spaces and alcoves.
• Staff and ancillary accommodation comprising
o Reception/administration office,
o Care staff office,
o Rest room with kitchenette,
o Staff locker/changing room,
o Staff shower and wc’s
o Laundry room,
o Sluice room,
o Catering kitchen with associated storage and staff facilities,
o Cleaners storage,
o Refuse stores,
o General storage,
o Main refuse hold, and
o Secure covered buggy storage with electric charging facilities.
• Plant and service equipment rooms,
• External spaces comprising,
o Sitting out/dining area,
o Residents garden,
o Secure residents garden,
o Therapy garden,
o Patio areas,
o Informal seating/rest areas,
o Car parking,
o Delivery vehicle access and parking,
o Visitor/resident drop off points, and
o Bicycle storage.
• Estimated cost of the construction works is £11.15M,

The consultant will become part of the Council’s in-house multi-disciplinary design team and will provide all services in conjunction with this team. The in-house team will be using BIM and the appointed consultant, where possible, will be expected to contribute to this throughout their commission.

The Council will be using the In-tend e-Tendering System for this Procurement exercise, please visit https://in-tendhost.co.uk/sandwellmbc to access the Sandwell MBC In-tend Supplier Portal.

From here you will be able to register your company, express an interest in the opportunity, and gain immediate access to the ITT and other related documents.

In Order To View the On-Line Questionnaire and Submit a Tender, you will be required to` Opt-In`.

Please be mindful that if you are cut and pasting your question responses onto the On-Line Questionnaire that you do so from a notepad document, this is due to the fact that some special characters are not accepted within the On-Line Questionnaire.

For a Step by Step user guide to the Sandwell MBC In-tend Supplier Portal please click on the `Guidance for Suppliers` section of the website. All procurement responses must be carried out via the Sandwell MBC In-tend Supplier Portal.

If you require further assistance in respect of the system please contact the In-tend support team on 0844 272 8810.

Closing date: Friday 16 December 2016 at 15:00hrs

M & E Engineering Design Services at Moor Lane Extra Care Scheme

Corporate Procurement | Published November 30, 2016  -  Deadline December 16, 2016
cpvs
71310000, 71311000, 71318000, 71315200, 71315210, 71530000, 79415200

M and E Engineering Design Services at Moor Lane Extra Care Scheme

The Council is looking to appoint a consultant to provide Mechanical & Electrical Engineering Design Services in accordance with the ACE Schedule of Services – Part G(b) Mechanical and electrical engineering (detailed design in buildings) Single Consultant or non-lead Consultant For use with ACE Agreement 1 – Design for an extra care facility in Moor Lane, Rowley Regis, West Midlands. The proposed accommodation would provide as a minimum the following:

• 60 one bedroom and 30 two bed room flats,
• Guest suite with en-suite bathroom,
• Combined lounge, dining and activities room, and kitchenette,
• Communal areas comprising
o Main lounge,
o Dining area,
o Residents tea kitchen,
o Communal wc’s,
o Assisted bathrooms, and
o Hairdressing & beauty therapy,
o Informal seating spaces and alcoves.
• Staff and ancillary accommodation comprising
o Reception/administration office,
o Care staff office,
o Rest room with kitchenette,
o Staff locker/changing room,
o Staff shower and wc’s
o Laundry room,
o Sluice room,
o Catering kitchen with associated storage and staff facilities,
o Cleaners storage,
o Refuse stores,
o General storage,
o Main refuse hold, and
o Secure covered buggy storage with electric charging facilities.
• Plant and service equipment rooms,
• External spaces comprising,
o Sitting out/dining area,
o Residents garden,
o Secure residents garden,
o Therapy garden,
o Patio areas,
o Informal seating/rest areas,
o Car parking,
o Delivery vehicle access and parking,
o Visitor/resident drop off points, and
o Bicycle storage.
• Estimated cost of the construction works is £11.15M,

The consultant will become part of the Council’s in-house multi-disciplinary design team and will provide all services in conjunction with this team. The in-house team will be using BIM and the appointed consultant, where possible, will be expected to contribute to this throughout their commission.

The Council will be using the In-tend e-Tendering System for this Procurement exercise, please visit https://in-tendhost.co.uk/sandwellmbc to access the Sandwell MBC In-tend Supplier Portal.

From here you will be able to register your company, express an interest in the opportunity, and gain immediate access to the ITT and other related documents.

In Order To View the On-Line Questionnaire and Submit a Tender, you will be required to` Opt-In`.

Please be mindful that if you are cut and pasting your question responses onto the On-Line Questionnaire that you do so from a notepad document, this is due to the fact that some special characters are not accepted within the On-Line Questionnaire.

For a Step by Step user guide to the Sandwell MBC In-tend Supplier Portal please click on the `Guidance for Suppliers` section of the website. All procurement responses must be carried out via the Sandwell MBC In-tend Supplier Portal.

If you require further assistance in respect of the system please contact the In-tend support team on 0844 272 8810.

Closing date: Friday 16 December 2016 at 15:00hrs

001/0570/16 C6276 Central Workshop and Store — Main Contractor

Translink | Published April 8, 2016  -  Deadline May 16, 2016
cpvs
45210000, 45213200, 45200000

The Northern Ireland Transport Holding Company NITHC is a public corporation established under the Transport Act NI 1967 to oversee the provision of public transport in Northern Ireland. It is responsible for the operation of its subsidiary companies, Citybus now Metro, NI Railways and Ulsterbus, which deliver passenger transport services. Translink is the brand name of the 3 operating companies, which operate integrated, scheduled bus and rail services in Northern Ireland, including cross border and cross channel links under a Public Service Obligation. Translink is one of Northern Ireland's largest employers, with over 3 500 employees, 80 000 000 passengers per annum and an annual turnover of 125 000 000. Translink wish to appoint a suitably qualified contractor to undertake building and civil engineering works in relation to the construction of a Workshop and Stores Facility in the Duncrue Street area of Belfast. The facility will house functional areas but not be limited to the following. The Bus Maintenance Workshop will require a mix of pits and bays to maintain both the regular Metro. Ulsterbus Fleet and the anticipated BRT Fleet, articulated 18.6 m buses. It is anticipated that there will be 2 No covered bus washes provided, 1 No drive through and 1 No programmable roll over wash, as well as a separate chassis wash 2 No drive through covered fuel issues would be linked to the bus wash lanes and would require accommodation for fuel logging and an accompanying Tank Farm. This area should also facilitate the cleaning of buses internally. Central Stores is a supporting function to bus maintenance in the Duncrue Street Facility and Greater Belfast Area. Typically it will require racking and shelving systems with access to the engineering workshop for forklift and or pallet trucks. An industrial lift may be provided to facilitate storage over 2 floors. M and E systems required within this area may include CCTV, Access Control and IT. Bus Engineering and Bus Operations will require ancillary accommodation to support their primary functions at this location. This may include driver pay in, offices, locker room, staff rest area, toilets etc. There may be some offices provided at this locations not linked to either Bus Engineering or Operations. Bus Parking is required for 70 to 80 standard buses and 30 BRT buses. Circa 200 spaces would be required for staff parking; this should be segregated from the bus parking. Generally, security fencing and gates, a security hut, vehicle barriers, lighting and CCTV will be provided within the depot. The delivery timescales for this project are determined by the BRT Programme. Maintenance functions and parking accommodation for the new Belfast Rapid Transit fleet BRT will be located on this new facility. The BRT fleet servicing period commences in Spring 2018, it is foreseen that a Sectional Completion of the bus wash and fuel issue complex, with parking for 30 BRT Vehicles, will be required at this point. The commencement of BRT service is scheduled for September 2018 and the new facility will need to be operational in advance of this. It is estimated that this will be an 18-month construction contract valued in the range 10 000 000 to 15 000 000.

001/0570/16 C6276 Central Workshop and Store — Main Contractor

Translink | Published April 8, 2016
cpvs
45210000, 45213200, 45200000

The Northern Ireland Transport Holding Company NITHC is a public corporation established under the Transport Act NI 1967 to oversee the provision of public transport in Northern Ireland. It is responsible for the operation of its subsidiary companies, Citybus now Metro, NI Railways and Ulsterbus, which deliver passenger transport services. Translink is the brand name of the 3 operating companies, which operate integrated, scheduled bus and rail services in Northern Ireland, including cross border and cross channel links under a Public Service Obligation. Translink is one of Northern Ireland's largest employers, with over 3 500 employees, 80 000 000 passengers per annum and an annual turnover of 125 000 000. Translink wish to appoint a suitably qualified contractor to undertake building and civil engineering works in relation to the construction of a Workshop and Stores Facility in the Duncrue Street area of Belfast. The facility will house functional areas but not be limited to the following. The Bus Maintenance Workshop will require a mix of pits and bays to maintain both the regular Metro. Ulsterbus Fleet and the anticipated BRT Fleet, articulated 18.6 m buses. It is anticipated that there will be 2 No covered bus washes provided, 1 No drive through and 1 No programmable roll over wash, as well as a separate chassis wash 2 No drive through covered fuel issues would be linked to the bus wash lanes and would require accommodation for fuel logging and an accompanying Tank Farm. This area should also facilitate the cleaning of buses internally. Central Stores is a supporting function to bus maintenance in the Duncrue Street Facility and Greater Belfast Area. Typically it will require racking and shelving systems with access to the engineering workshop for forklift and or pallet trucks. An industrial lift may be provided to facilitate storage over 2 floors. M and E systems required within this area may include CCTV, Access Control and IT. Bus Engineering and Bus Operations will require ancillary accommodation to support their primary functions at this location. This may include driver pay in, offices, locker room, staff rest area, toilets etc. There may be some offices provided at this locations not linked to either Bus Engineering or Operations. Bus Parking is required for 70 to 80 standard buses and 30 BRT buses. Circa 200 spaces would be required for staff parking; this should be segregated from the bus parking. Generally, security fencing and gates, a security hut, vehicle barriers, lighting and CCTV will be provided within the depot. The delivery timescales for this project are determined by the BRT Programme. Maintenance functions and parking accommodation for the new Belfast Rapid Transit fleet BRT will be located on this new facility. The BRT fleet servicing period commences in Spring 2018, it is foreseen that a Sectional Completion of the bus wash and fuel issue complex, with parking for 30 BRT Vehicles, will be required at this point. The commencement of BRT service is scheduled for September 2018 and the new facility will need to be operational in advance of this. It is estimated that this will be an 18-month construction contract valued in the range 10 000 000 to 15 000 000.

Barry Fire Station Co-Location Works

South Wales Fire and Rescue Service | Published May 2, 2017
cpvs
45210000

South Wales Fire and Rescue Service are looking to appoint a contractor to carry out works to accommodate a co-location facility at Barry Fire Station. Concept design plans have been produced and will include the following work; o Complete strip out of first floor including all M&E. o Fit out to the first floor to the new layout indicated. o Upgrade of external fabric to the main elevations to enhance finishes and appearance. o Minor extension to the rear of the appliance bay to include a new store. This being a load bearing masonry solution with heating, power, lighting and slab / foundation design. o Structural alternations to ensure existing waffle type slab remains in tack and roof supported. Structural works to also review the existing side walls at first floor with the potential for new wind posts as required. o New M&E installation including upgrade to access control and fire alarm system. o New fire escape stair o Drainage alterations internally to take new showers and WC’s at first floor and amended washrooms and kitchen at ground floor. o New finishes throughout first floor and areas where alteration will occur at ground floor, namely kitchen / mess, offices, WC’s, showers, locker rooms, muster and drying room. o New sliding folding partition at first floor including structural support. o Upgrade or new windows / doors as required. o New sanitary ware and FFE as indicated. o New lift installation including M&E and structural alterations. o Alteration of wall locations at ground floor that may prove to have load bearing properties. o External works as indicated to ensure maximisation of parking and altered access / egress proposal by re-aligning internal levels and kerbs to create a one way deployment route. o Re-surfacing works externally. o Allowance for provision of a new covered steel structure at the rear of the service yard. o Upgrades to external lighting. o Review of existing M&E loadings and recommendation for any upgrade works. Outline existing and proposed sketch plans are attached for reference. A design team has recently been appointed to carry out a fully coordinated detailed design and set of Employers Requirements for the purpose of the ITT stages. The team is as follows: Lawray Architects - Lead Consultant, Architect, Principle Designer and Contract Administrator Bingham Hall Partnership - Structural and Civil Engineers DRAC Consulting - Mechanical and Electrical Consultants TC Consult - Cost Consultant The client team consists of Estates representatives from both South Wales Fire and Rescue Service and Welsh Ambulance Service NHS Trust. NOTE: To register your interest in this notice and obtain any additional information please visit the Sell2Wales Web Site at http://www.sell2wales.gov.wales/Search/Search_Switch.aspx?ID=65963. The buyer has indicated that it will accept electronic responses to this notice via the Postbox facility. A user guide is available at http://www.sell2wales.gov.wales/sitehelp/help_guides.aspx. Suppliers are advised to allow adequate time for uploading documents and to dispatch the electronic response well in advance of the closing time to avoid any last minute problems.

Repair and maintenance services of building installations

South Wales Fire and Rescue Service | Published May 4, 2017
Winner
Trio Building Contractors Ltd
cpvs
50700000, 45442110, 45330000

South Wales Fire and Rescue Service is seeking to appoint suitably qualified and experienced contractors to provide General Maintenance Services which will comprise of Minor Projects, Painting and Decorating, Plumbing Services and General and Reactive Maintenance on premises throughout South Wales Fire and Rescue Services.

The contract will be split into 4 lots, and suppliers will have the opportunity to bid for one or more lots.

Lot 1 — Minor Projects.

The requirement is to provide an all trades service to carry out minor projects up to the value of 75 000 GBP. Past projects include creating Lecture Rooms and Kitchens from a Storage Area and creating Locker Rooms and Mess Rooms from a large Dining Area. Each project is different and will cater for the needs of each individual site.

The trades required are:

— Carpenters,

— Joiners,

— Electricians,

— Plumbers,

— Painter — Decorators,

— Plasterers,

— Floor layers,

— Tilers,

— Foremen,

— Site Managers,

— Site Supervisors.

The service will require the successful company to be able to supply each of the above trades on an ad hock basis. When carrying out a project it is essential that all trades are readily available to complete the project to our tight timescales.

The service is to comprise of the painting and decorating Fire Services Premises across South Wales as and when required.

The service is to include but not restricted to:

— Filling,

— Sanding,

— Painting,

— Glossing,

— Patching,

— Stain blocking,

— Varnishing,

— Staining,

— Spraying.

The service is to comprise of Plumbing Services to Fire Services Premises across South Wales.

The service is to include but not restricted to:

— Sanitary repairs/replacements and blockages,

— Drainage,

— Dehumidifier repairs/replacement,

— Hot water boiler repairs/replacement up to 45KW,

— Combination boiler repairs/replacement,

— Legionella defects and recommendations,

— Hose reels.

The service is to comprise of the repair to all internal and external building fabric and associated external ground repairs, up to the value of 5 000 GBP.

The service is to include:

— All carpentry and joinery,

— Roofing,

— Cleaning of gutters and down pipes,

— Flooring,

— Window repairs or replacement,

— Door repairs or replacements,

— Repairs to out buildings,

— Repairs or rebuilding of brick work,

— Tiling,

— Fencing,

— Boundary walls,

— Repairs to drill towers,

— Plastering.

St Mary's Airport Terminal Project.

Council of the Isles of Scilly | Published April 19, 2014
Winner
Lagan Construction LtdRosemount House, 21-23 Sydenham RoadBelfast BT3 9HA +44 2890455531 www.laganconstructiongroup.com+44 2890458940
cpvs
45000000, 45213000, 45213300, 45213330, 45213331, 45213333, 45213400

The project concerns the redevelopment of the existing terminal on St Mary's. This will include providing an improved passenger experience through upgrading of the departures and arrivals areas through a new facade extension, improved check In and queuing area, improved customer information monitors, better seating, draught-proofing, refurbished cafe area and relocated cafe kitchen, better natural and artificial lighting, refurbished passenger WC's, complete redecoration, replacement of the windows and Improving thermal performance (roof insulation). The project will also focus on the provisions for airport staff including new and relocated check-in desks, an increase in the number of administration offices for carriers with dedicated kitchen area, new baggage weigh-in and tagging systems, new baggage conveyor, future space allowance for X ray of baggage and new locker rooms and associated welfare facilities. Improvements are also required to the "airside" elements of the terminal including an enlarged and reconfigured baggage handling & FF&R ancillary spaces, better space for handling of freight/packages, reconfigured belt, space for five baggage tugs with trailers for overnight storage, undercover loading, new crew room with kitchenette area, eating, seating area, new staff toilets and shower room, ready room for ATC staff, refurbishment/upgrading of existing control desks and associated instrumentation/hardware to the ATC Tower and improved sun-screening/shading to windows of ATC Tower room Externally, the works will include an external walled ‘garden' area, rationalisation of the external spaces including parking, landscaping, signage, pick-up and drop-off zones and new external storage and the provision of a canopy to inbound arrivals and outbound departures areas. Additionally, the project will seek to include solar photovoltaic panels for the generation of electricity for the terminal building.

St Mary's Airport Terminal Project.

Council of the Isles of Scilly | Published September 10, 2013  -  Deadline October 7, 2013
cpvs
45000000, 45213000, 45213300, 45213330, 45213331, 45213333, 45213400

The project concerns the redevelopment of the existing terminal on St Mary's. This will include providing an improved passenger experience through upgrading of the departures and arrivals areas through a new facade extension, improved check In and queuing area, improved customer information monitors, better seating, draught-proofing, refurbished cafe area and relocated cafe kitchen, better natural and artificial lighting, refurbished passenger WC's, complete redecoration, replacement of the windows and Improving thermal performance (roof insulation). The project will also focus on the provisions for airport staff including new and relocated check-in desks, an increase in the number of administration offices for carriers with dedicated kitchen area, new baggage weigh-in and tagging systems, new baggage conveyor, future space allowance for X ray of baggage and new locker rooms and associated welfare facilities. Improvements are also required to the "airside" elements of the terminal including an enlarged and reconfigured baggage handling and FF&R ancillary spaces, better space for handling of freight/packages, reconfigured belt, space for five baggage tugs with trailers for overnight storage, undercover loading, new crew room with kitchenette area, eating, seating area, new staff toilets and shower room, ready room for ATC staff, refurbishment/upgrading of existing control desks and associated instrumentation/hardware to the ATC Tower and improved sun-screening/shading to windows of ATC Tower room. Externally, the works will include an external walled ‘garden' area, rationalisation of the external spaces including parking, landscaping, signage, pick-up and drop-off zones and new external storage and the provision of a canopy to inbound arrivals and outbound departures areas. Additionally, the project will seek to include solar photovoltaic panels for the generation of electricity for the terminal building.

Purchase of Rigid Inflatable Boat

Port William Inshore Rescue Service | Published March 20, 2014
cpvs

6.4mt Commercial specification rigid inflatable boat (orange) including the following: Hypalon inflation tubes (orange) external tube looped lifelines,with 'D' ring tube patches (grey/black) 'D' section rubbing strake fendering (grey/back) Anti slip decking (grey/black) Black upholstery under decking trunk system for all cables aft deck water collection sump elephant trunk style deck drainers 4" min stainless steel bow winch eye strong point and transom mounted towing eyes. Rule bilge pump wired to console, includes skin fitting, hose and carling switch. foot pump and emergency tube repair kit. anchor locker, hatch and deck tie off cleat. lifeboat console complete with side access hatch includes 3 upholstered seats, protex seat latches, seat gasket, drain holes and access hatch. Console extras - bow deck bollard with reinforcing plate. Anchor rope stowage reel with detachable handle. anchor storage, chain bucket and storage hypalon covered foam cover for chain bucket and bow deck bollard. Back rests to be non grab handle type and back pad to be square at top. Fuel system - 2 x twin 20 gallon stainless steel under deck fuel tank with water separating fuel filter, console recess filler, perko filler with integrated breather, emergency shut off valve, electronic fuel sender and guage ISO 21487.2 x Fuel cross over valve and emergency shut off valves. 2 x Clean out ports. A Frame - Aluminium self righting frame, powder coated in black. Complete with brackets for optional navigation lights, aerials with inflation bag and manually activated firing head and cylinder. Echomax midi radar reflector mounted to A frame. Tow spreader bar with stowage. Fold down top mast. Tube accessories - 5x over pressure release valves, one per chamber. 1500gsm Hypalon. paddles and tube mounted retainers. 4 x rubber grab handle bonded to tube. reinforced tubes at bow-200mm above D section. 2 x tube mounted storage bags. 8 x wear patches bonded to tube. 8 x solas reflective patches 4" by 12". fitting and installation of 2 outboard motors - 90hp four stroke, propeller, tachometer, trim guage, remote control box plus warranty. road trailer - twin axle multi roller coaster, jockey wheel, spare wheel, mudguards, light board, bars plus warranty.

Purchase of Rigid Inflatable Boat

Port William Inshore Rescue Service | Published May 6, 2014
Winner
Ribcraft Ltd
cpvs

6.4mt Commercial specification rigid inflatable boat (orange) including the following: Hypalon inflation tubes (orange) external tube looped lifelines,with 'D' ring tube patches (grey/black) 'D' section rubbing strake fendering (grey/back) Anti slip decking (grey/black) Black upholstery under decking trunk system for all cables aft deck water collection sump elephant trunk style deck drainers 4" min stainless steel bow winch eye strong point and transom mounted towing eyes. Rule bilge pump wired to console, includes skin fitting, hose and carling switch. foot pump and emergency tube repair kit. anchor locker, hatch and deck tie off cleat. lifeboat console complete with side access hatch includes 3 upholstered seats, protex seat latches, seat gasket, drain holes and access hatch. Console extras - bow deck bollard with reinforcing plate. Anchor rope stowage reel with detachable handle. anchor storage, chain bucket and storage hypalon covered foam cover for chain bucket and bow deck bollard. Back rests to be non grab handle type and back pad to be square at top. Fuel system - 2 x twin 20 gallon stainless steel under deck fuel tank with water separating fuel filter, console recess filler, perko filler with integrated breather, emergency shut off valve, electronic fuel sender and guage ISO 21487.2 x Fuel cross over valve and emergency shut off valves. 2 x Clean out ports. A Frame - Aluminium self righting frame, powder coated in black. Complete with brackets for optional navigation lights, aerials with inflation bag and manually activated firing head and cylinder. Echomax midi radar reflector mounted to A frame. Tow spreader bar with stowage. Fold down top mast. Tube accessories - 5x over pressure release valves, one per chamber. 1500gsm Hypalon. paddles and tube mounted retainers. 4 x rubber grab handle bonded to tube. reinforced tubes at bow-200mm above D section. 2 x tube mounted storage bags. 8 x wear patches bonded to tube. 8 x solas reflective patches 4" by 12". fitting and installation of 2 outboard motors - 90hp four stroke, propeller, tachometer, trim guage, remote control box plus warranty. road trailer - twin axle multi roller coaster, jockey wheel, spare wheel, mudguards, light board, bars plus warranty.

Internal Refurbishment Works

Homes and Communities Agency | Published November 5, 2013  -  Deadline November 19, 2013
cpvs
45453100

The Homes and Communities Agency wish to appoint a Principal Contractor to complete the proposed internal refurbishment works in accordance with the specification documents prepared by GVA Grimley Ltd. The chosen contractor will be appointed under the terms of a JCT Minor Works Building Contract with Contractor’s Design Form of Contract 2011 Edition. The contract is to be administered by the HCA’s Lead Consultant, GVA Grimley Ltd. The Homes and Communities Agency (HCA) occupy St George’s House. The three-storey office building was built in 1936 and there have been a number of refurbishments to both the internal and external fabric of the property during that time. There is a Kitchen area on both ground and first floors along with a tea point facility again on ground and first floors of the building. The current arrangements were fitted as part of the major refurbishment works in 1998. The refurbishment works to the kitchen/tea point areas include renewal of all the existing fittings (base/wall mounted units) inclusive of kitchen sinks, worktops, etc, as well as floor coverings, suspended ceilings and redecoration. All integrated appliances including dishwashers, fridges, etc also require replacing. Works to the kitchen/tea point areas will include a small amount of service alteration works. All new fittings are to be fitted to the existing service/drainage provisions where possible. The existing ground floor south wing former Post Room is to be converted into 2no separate shower rooms inclusive of common locker space. Proposed works are to include re-configuration of the existing layout including removal of the existing internal dividing wall, as well as new floor, wall and ceiling finishes. New service installations/drainage disposal are to be provided connected into the nearby services, as well as lighting, small power and mechanical extraction provision. New showers are to be electrically operated. All service installations associated with the new showers are to be designed and installed by the appointed contractor. Other works include the removal of a number of internal dividing walls to the first floor office space in order to provide open plan space inclusive of making good any retained finishes.

Integrated Workspace Management Solution (IWMS)

Digital Service | Published August 10, 2016  -  Deadline September 15, 2016
cpvs
48421000, 48420000

The Houses of Parliament are considering options for replacing its current Facilities Management system with an Integrated Workspace Management Solution (IWMS) to deliver efficiencies by improving processes; introducing modern tools to allocate/schedule work, enabling remote/mobile working; improving management reporting, and consolidating a number of disparate specialist systems that manage:

- Reactive, Planned Maintenance and Helpdesk
- Space, Moves (staff/departments) and Furnishings
- Accidents, Incidents and Risk Assessments
- Fire and Risk Management
- Environmental Compliance
- Asset Surveys
- Project Management

It is critical that that our ICT systems in Parliament incorporate essential technologies to not only support our business processes across both Houses, but also contribute significantly in helping us meet our business critical priorities.

We wish to investigate enhancements to existing capabilities and internal workflows in number of areas; our potential partners are encouraged to express an interest in this opportunity if their proposal is able to address all the essential areas identified below (please note that this is NOT an exhaustive list):

1. Workplace Management
a. Moves Managements
Create new moves
Re-schedule moves
Request office furnishing
IT equipment and telephone relocation
Self service capability with customer notifications

b. Space Management
Space planning
Label floor plans
Assign office spaces to a role
Occupant Information
View locker assignment
View office space network/power ports

2. Reactive Maintenance
c. Comprehensive Support Desk
Log over 20,000 work requests via telephone or online
Create and assign tasks via a virtual work scheduling system including the ability for customers to book specific time slots for work
Match resources to skills required
Define Service Level Agreements (SLA) with customers and contractors
Provide Traffic Light dashboard reporting of all key SLA information
Manage workflow processes including supporting mobile working technology to provide “live” progress reports so users can monitor request progress

3. Planned Maintenance.
d. Asset Management
Allow assets to be created and managed through life cycle including use of bar codes
Allow planned maintenance to be allocated against assets
Provide full integration with the SFG20 suite of software to allow seamless transfer of data

4. Lease/Contract Management
e. Lease Management
View and update contract data for rental, lease and ground lease contracts
Track contract expirations through automated alerts
View Financial data such as Commercial value, book value and insurance value

5. Inventory
f. Track and Manage Stock
View current stock levels across items by value and location(s)
Automatically update stock totals as part of maintenance tasks when required
Allocate suppliers and prices to stock items
Receipt incoming stock and record outgoing stock

6. Health and Safety
g. Compliance
Record accidents, incidents and near misses including subsequent investigations
Record risk assessments
Link accidents to risk assessments
Link risk assessments to work tasks
COSHH assessments
Issue work permits

We expect the proposed solution to support current and emerging Building Information Modelling (BIM) requirements, and our partner to provide a clear roadmap for their product development as well as demonstrate capability and leadership in the IWMS space.

IWMS Platform Capabilities - The potential system will be used across key functions in the Houses of Parliament:

Maintenance
Accommodation & Logistics
Property, Planning & Design

Key stakeholders in Parliament will include, but are not limited to, Senior Managers, Contractors, Engineers, Maintenance Staff, Estate Project Managers, Technical and Project Management Resources.

This is expected to be a long-term contract, with an initial 3-year term, and the estimated value of the contract is expected to exceed £1,000,000 (exclusive of VAT).

We expect the new system will be required from early to mid-2017. In line with Parliament’s ICT cloud first policy, we will be considering a cloud-based solution, although other solutions will also be considered.

Please note this is Prior Information Notice. Please submit your expressions of interest via our In-Tend procurement portal https://in-tendhost.co.uk/parliamentuk/aspx/Home. Please note there are no tender documents to download or submit at this stage, but there is a document displaying the IWMS Platform Capabilities which can be viewed on the portal. Please note that the deadline for expressions of interest is 09:30 hours UK time on Friday 16th of September 2016.


M & E Engineering Design Services at Moor Lane Extra Care Scheme - AWARD

Sandwell Metropolitan Borough Council | Published March 24, 2017  -  Deadline December 16, 2016
Winner
S I Sealy & Associates Ltd
cpvs
71310000

M and E Engineering Design Services at Moor Lane Extra Care Scheme The Council is looking to appoint a consultant to provide Mechanical & Electrical Engineering Design Services in accordance with the ACE Schedule of Services - Part G(b) Mechanical and electrical engineering (detailed design in buildings) Single Consultant or non-lead Consultant For use with ACE Agreement 1 - Design for an extra care facility in Moor Lane, Rowley Regis, West Midlands. The proposed accommodation would provide as a minimum the following: o 60 one bedroom and 30 two bed room flats, o Guest suite with en-suite bathroom, o Combined lounge, dining and activities room, and kitchenette, o Communal areas comprising o Main lounge, o Dining area, o Residents tea kitchen, o Communal wc's, o Assisted bathrooms, and o Hairdressing & beauty therapy, o Informal seating spaces and alcoves. o Staff and ancillary accommodation comprising o Reception/administration office, o Care staff office, o Rest room with kitchenette, o Staff locker/changing room, o Staff shower and wc's o Laundry room, o Sluice room, o Catering kitchen with associated storage and staff facilities, o Cleaners storage, o Refuse stores, o General storage, o Main refuse hold, and o Secure covered buggy storage with electric charging facilities. o Plant and service equipment rooms, o External spaces comprising, o Sitting out/dining area, o Residents garden, o Secure residents garden, o Therapy garden, o Patio areas, o Informal seating/rest areas, o Car parking, o Delivery vehicle access and parking, o Visitor/resident drop off points, and o Bicycle storage. o Estimated cost of the construction works is ?11.15M, The consultant will become part of the Council's in-house multi-disciplinary design team and will provide all services in conjunction with this team. The in-house team will be using BIM and the appointed consultant, where possible, will be expected to contribute to this throughout their commission. The Council will be using the In-tend e-Tendering System for this Procurement exercise, please visit https://in-tendhost.co.uk/sandwellmbc to access the Sandwell MBC In-tend Supplier Portal. From here you will be able to register your company, express an interest in the opportunity, and gain immediate access to the ITT and other related documents. In Order To View the On-Line Questionnaire and Submit a Tender, you will be required to` Opt-In`. Please be mindful that if you are cut and pasting your question responses onto the On-Line Questionnaire that you do so from a notepad document, this is due to the fact that some special characters are not accepted within the On-Line Questionnaire. For a Step by Step user guide to the Sandwell MBC In-tend Supplier Portal please click on the `Guidance for Suppliers` section of the website. All procuremen...

Ward and Residential Furniture

NHS SUPPLY CHAIN | Published October 30, 2017  -  Deadline April 18, 2017
Winner
Craftwork Upholstery Limited
cpvs
39100000

OJEU Ref - 2017/S 056-104552 CPV Codes - 39100000 39110000 39112000 39112100 39113000 39113100 39113200 39113600 39113700 39114000 39120000 39121200 39122000 39143000 39143100 39143113 39143123 33196100 33196200 NHS Supply Chain seeks to establish a non-exclusive Framework Agreement for supply to NHS Supply Chain customer base via the Direct Route. The scope of the framework is to cover all Ward and Residential Furniture used within but not limited to the following environments: - Wards; - Waiting Areas; - Out Patients; - Family Areas; - Dining Areas; - Lounge Areas; - Reception Areas; - Overnight Stay. This Framework Agreement is for 24 months with the option to extend in incremental stages for up to a total period of 48 months. There are a total of 20 product lines within the basket which are set out in the 'Lot Line Detail' tab and are detailed below: Patient High Backed Chair; Visitor Stacking Chair; Bariatric Armchair; Bedside Locker; Overbed/Overchair Table; 1 Seater Settee; 2 Seater Settee; 3 Seater Settee; Wardrobe; Chest of Drawers; Dressing Table; Bedside Cabinet; Low Back Easy Chair; Stacking Chair; Dining Chair; Manual Reclining Chair; Electric Reclining Chair; Coffee Table; Dining Table and Beam Seating. Applicants must be able to provide at least 13 of 20 lines within the basket. If Applicants are unable to meet this requirement then NHS Supply Chain reserves the right to exclude the Applicant from the procurement process and not to consider the tender response for this Framework Agreement any further. NHS Supply Chain anticipates awarding all Applicants who meet the minimum requirements which are set out in these tender documents and whose Average Basket Score (based on the methodology and definition as stated within Sections 8.3 - 8.5 of this document) meets or exceeds a hurdle of at least 55 % (when rounded up or down from four decimal places (as the case may be) to the nearest whole number) at tender evaluation stage will be awarded all of the product lines submitted for evaluation and should these Applicants be able over the lifetime of the Framework Agreement to supply any of the other product lines in the Basket such Applicants will be given the opportunity to do so. Please note that Applicants must submit a bid against all evaluated product lines which they intend to supply under the Framework Agreement. If pricing has not been submitted for a particular product line and an applicant is able to supply that particular product line at the time of the Tender submission then NHS Supply Chain reserves the right to not allow the applicant (if successful) to supply that particular product line over the lifetime of the Framework Agreement. NHS Supply Chain has taken the decision not to sub-divide this Framework Agreement into Lots on the basis that the range of products would be suitable for a basket of goods as the products are broadly similar and the total value would be more attractive to the supply base.

Partial Refurbishment of Penketh Centre, Warrington -CPA/SPU/135

Cheshire Constabulary | Published October 3, 2011  -  Deadline October 16, 2011
cpvs
45453100, 50700000

Cheshire Police Authority invite expressions of interest from suitably experienced, resourced and competent Building Contractors to carry out proposed refurbishment and alteration works.

 

Due to the nature of the works, it is anticipated that building contractors will be working in a lead/prime contractor role, with sub—contractors working with them on the project.  The Authority are seeking to award one contract for all the works, applications for individual component parts will not be progressed.

 

The works comprises the partial refurbishment and alterations of a existing Community Centre, (280 sq.m) to provide facilities for Cheshire Police.  The building is single storey of traditional construction. The works include general office refurbishment comprising of removing/installing partitions, structural work, new floor finishes, suspended ceilings, general redecoration & wall tiling, provision of additional WC’s and locker facilities.   New lighting, power, data distribution and alterations to the fire alarm system will be required.  The installation of a new heating system and provision of a new boiler will form part of the works.  The premises will be vacant throughout the works. 

 

Contractors must have the ability to prove refurbishments of a similar size and nature and references will be sought (refer to the pre-qualification questionnaire).  Contractors responding in a lead/prime contractor role will be required to prove robust arrangements for selection and management of any sub-contractors.

 

At Expression of Interest/Pre-Qualification Questionnaire stage, no site visit is possible or required.  A site visit opportunity for those contractors invited to tender will take place on Tuesday 22 November 2011.

 

Budget Cost

 

The estimated budget for the works is in the range £145-£165k.  The budget estimate is being provided to enable economic operators to understand the value scope of the works and therefore to determine whether this opportunity is of interest.  It is estimated that there will be approximately an equal split between labour and materials.

 

Contract Term

 

The contract will be tendered during November 2011 and the contract is anticipated to be awarded mid-December 2011.   It is planned that work will commence on site 23 January 2012 with a preferred completion date no later than 20 April 2012.    Contractors are requested only to express interest if they have the capacity to meet the timescales required.

 

Expression of Interest

 

Expressions of Interest are all being handled through the advertised opportunity on www.bluelight.gov.uk.    If you are reading this advertisement other than on the Bluelight website - If you visit www.bluelight.gov.uk click on “New Opportunities” link within the Supplier Area, Select Cheshire Constabulary from the Organisation drop-down list, then click on the opportunity you are interested in.  Then click the login and register interest button.

 

General Building Maintenance Services

South Wales Fire and Rescue Service | Published May 4, 2017
cpvs
50700000

South Wales Fire and Rescue Service is seeking to appoint suitably qualified and experienced contractors to provide General Maintenance Services which will comprise of Minor Projects, Painting and Decorating, Plumbing Services and General and Reactive Maintenance on premises throughout South Wales Fire and Rescue Services. The contract will be split into 4 lots, and suppliers will have the opportunity to bid for one or more lots. II.1.6) Information about lots This contract is divided into lots: Yes II.1.7) Total value of the procurement Value excluding VAT: 500 000.00 GBP II.2) Description Lot No: 1 II.2.1) Title Minor Projects II.2.2) Additional CPV code(s) 50700000 II.2.3) Place of performance NUTS code: UKL Main site or place of performance: Premises within the boundary of South Wales Fire and Rescue Service II.2.4) Description of the procurement Lot 1 – Minor Projects The requirement is to provide an all trades service to carry out minor projects up to the value of 75k GBP. Past projects include creating Lecture Rooms and Kitchens from a Storage Area and creating Locker Rooms and Mess Rooms from a large Dining Area. Each project is different and will cater for the needs of each individual site. The trades required are: - Carpenters - Joiners - Electricians - Plumbers - Painter – Decorators - Plasterers - Floor layers - Tilers - Foremen - Site Managers - Site Supervisors The service will require the successful company to be able to supply each of the above trades on an ad hock basis. When carrying out a project it is essential that all trades are readily available to complete the project to our tight timescales II.2.5) Award criteria Quality criterion: Quality / Weighting: 30 Price / Weighting: 70 II.2.11) Information about options Options: No II.2.13) Information about European Union funds The procurement is related to a project and/or programme financed by European Union funds: No Lot No: 2 II.2.1) Title Painting and Decorating II.2.2) Additional CPV code(s) 45442110 II.2.3) Place of performance NUTS code: UKL Main site or place of performance: Premises within the boundary of South Wales Fire and Rescue Service. II.2.4) Description of the procurement The service is to comprise of the painting and decorating Fire Services Premises across South Wales as and when required. The service is to include but not restricted to: - Filling - Sanding - Painting - Glossing - Patching - Stain blocking - Varnishing - Staining - Spraying II.2.5) Award criteria Quality criterion: Quality / Weighting: 30 Price / Weighting: 70 II.2.11) Information about options Options: No II.2.13) Information about European Union funds The procurement is related to a project and/or programme financed by European Union funds: No Lot No: 3 II.2.1) Title Plumbing Services II.2.2) Additional CPV code(s) 45330000 II.2.3) Place of performance NUTS code: UKL Main site or place of performance: Premises within the boundary of South Wales Fire and Rescue Service area. II.2.4) Description of the procurement The service is to comprise of Plumbing Services to Fire Services Premises across South Wales. The service is to include but not restricted to: - Sanitary repairs/replacements and blockages - Drainage - Dehumidifier repairs/replacement - Hot water boiler repairs/replacement up to 45KW - Combination boiler repairs/replacement - Legionella defects and recommendations - Hose reels II.2.5) Award criteria Quality criterion: Quality / Weighting: 30 Price / Weighting: 70 II.2.11) Information about options Options: No II.2.13) Information about European Union funds The procurement is related to a project and/or programme financed by European Union funds: No Lot No: 4 II.2.1) Title General and Reactive Maintenance II.2.2) Additional CPV code(s) 50700000 II.2.3) Place of performance NUTS code: UKL Main site or place of performance: Premises within the boundary of South Wales Fire and Rescue Service area. II.2.4) Description of the procurement The service is to comprise of the repair to all internal and external building fabric and associated external ground repairs, up to the value of 5k GPB. The service is to include: - All carpentry and joinery - Roofing - Cleaning of gutters and down pipes - Flooring - Window repairs or replacement - Door repairs or replacements - Repairs to out buildings - Repairs or rebuilding of brick work - Tiling - Fencing - Boundary walls - Repairs to drill towers - Plastering II.2.5) Award criteria Quality criterion: Quality / Weighting: 30 Price / Weighting: 70 II.2.11) Information about options Options: No II.2.13) Information about European Union funds The procurement is related to a project and/or programme financed by European Union funds: No Section IV: Procedure IV.1) Description IV.1.1) Type of procedure Restricted procedure IV.1.3) Information about a framework agreement or a dynamic purchasing system The procurement involves the establishment of a framework agreement IV.1.8) Information about Government Procurement Agreement (GPA) The procurement is covered by the Government Procurement Agreement: Yes IV.2) Administrative information IV.2.1) Previous publication concerning this procedure Notice number in the OJ S: 2016/S 209-378449 Section V: Award of contract Lot No: 1 Title: Minor Projects A contract/lot is awarded: Yes V.2 Award of contract V.2.1) Date of conclusion of the contract 28/04/2017 V.2.2) Information about tenders Number of tenders received: 6 Number of tenders received from SMEs: 6 Number of tenders received from tenderers from other EU Member States: 6 Number of tenders received from tenderers from non-EU Member States: 0 Number of tenders received by electronic means: 6 The contract has been awarded to a group of economic operators: Yes V.2.3) Name and address of the contractor Trio Building Contractors LTD Unit 5B, Cambrian Industrial Estate East Side, Coedcae Lane Pontyclun CF72 9EW UK Telephone: +44 7803283724 NUTS: UKL The contractor is an SME: Yes V.2.3) Name and address of the contractor WILLIS CONSTRUCTION LTD WILLIS CONSTRUCTION LTD, Unit 6 Melyn Mair Business Centre Rumney CARDIFF CF3 2EX UK Telephone: +44 2920797073 Fax: +44 2920798379 NUTS: UKL22 The contractor is an SME: Yes V.2.3) Name and address of the contractor FACILITY SERVICES GROUP LTD Penllergaer Business Park, Penllergaer Swansea SA4 9HL UK Telephone: +44 1792898040 Fax: +44 1792875014 NUTS: UKL The contractor is an SME: Yes V.2.4) Information on value of the contract/lot (excluding VAT) Total value of the contract/lot: 500 000.00 GBP V.2.5) Information about subcontracting Section V: Award of contract Lot No: 2 Title: Painting and Decorating A contract/lot is awarded: Yes V.2 Award of contract V.2.1) Date of conclusion of the contract 02/05/2017 V.2.2) Information about tenders Number of tenders received: 2 Number of tenders received from SMEs: 2 Number of tenders received from tenderers from other EU Member States: 2 Number of tenders received from tenderers from non-EU Member States: 0 Number of tenders received by electronic means: 2 The contract has been awarded to a group of economic operators: No V.2.3) Name and address of the contractor FACILITY SERVICES GROUP LTD Penllergaer Business Park, Penllergaer Swansea SA4 9HL UK Telephone: +44 1792898040 Fax: +44 1792875014 NUTS: UKL The contractor is an SME: Yes V.2.4) Information on value of the contract/lot (excluding VAT) Total value of the contract/lot: 500 000.00 GBP V.2.5) Information about subcontracting Section V: Award of contract Lot No: 3 Title: Plumbing Services A contract/lot is awarded: Yes V.2 Award of contract V.2.1) Date of conclusion of the contract 28/04/2017 V.2.2) Information about tenders Number of tenders received: 4 Number of tenders received from SMEs: 4 Number of tenders received from tenderers from other EU Member States: 4 Number of tenders received from tenderers from non-EU Member States: 0 Number of tenders received by electronic means: 4 The contract has been awarded to a group of economic operators: No V.2.3) Name and address of the contractor Trio Building Contractors LTD Unit 5B, Cambrian Industrial Estate East Side, Coedcae Lane Pontyclun CF72 9EW UK Telephone: +44 7803283724 NUTS: UKL The contractor is an SME: Yes V.2.4) Information on value of the contract/lot (excluding VAT) Total value of the contract/lot: 500 000.00 GBP V.2.5) Information about subcontracting Section V: Award of contract Lot No: 4 Title: General and Reactive Maintenance A contract/lot is awarded: Yes V.2 Award of contract V.2.1) Date of conclusion of the contract 28/04/2017 V.2.2) Information about tenders Number of tenders received: 3 Number of tenders received from SMEs: 3 Number of tenders received from tenderers from other EU Member States: 3 Number of tenders received from tenderers from non-EU Member States: 0 Number of tenders received by electronic means: 3 The contract has been awarded to a group of economic operators: No V.2.3) Name and address of the contractor Trio Building Contractors LTD Unit 5B, Cambrian Industrial Estate East Side, Coedcae Lane Pontyclun CF72 9EW UK Telephone: +44 7803283724 NUTS: UKL The contractor is an SME: Yes V.2.4) Information on value of the contract/lot (excluding VAT) Total value of the contract/lot: 500 000.00 GBP V.2.5) Information about subcontracting Section VI: Complementary information VI.3) Additional information Please note this is a CONTRACT AWARD (WA Ref:65943) VI.4) Procedures for review VI.4.1) Review body South Wales Fire and Rescue Service South Wales Fire and Rescue Service Headquarters, Forest View Business Park, Llantrisant Llantrisant CF72 8LX UK Telephone: +44 1443232755 Fax: +44 1443232180 Internet address(es) URL: www.southwales-fire.gov.uk VI.5) Date of dispatch of this notice 02/05/2017 Information added to the notice since publication. Additional information added to the notice since it's publication. No further information has been uploaded. Main Contact: j-snooks@southwales-fire.gov.uk Admin Contact: N/a Technical Contact: N/a Other Contact: N/a Commodity Categories Commodity Categories IDTitleParent Category 45442110Painting work of buildingsApplication work of protective coatings 45330000Plumbing and sanitary worksBuilding installation work 50700000Repair and maintenance services of building installationsRepair and maintenance services Delivery Locations Delivery Locations IDDescription 1017Bridgend and Neath Port Talbot 1022Cardiff and Vale of Glamorgan 1015Central Valleys (Merthyr Tydfil, Rhondda Cynon Taf) 1013Conwy and Denbighshire 1020East Wales 1023Flintshire and Wrexham 1016Gwent Valleys (Torfaen, Blaenau Gwent, Caerphilly) 1012Gwynedd 1011Isle of Anglesey 1021Monmouthshire and Newport 1024Powys 1014South West Wales (Carmarthenshire, Pembrokeshire, Ceredigion) 1018Swansea 100UK - All 1000WALES 1010West Wales and The Valleys Alert Region Restrictions The buyer has restricted the alert for this notice to suppliers based in the following regions. Alert Region Restrictions There are no alert restrictions for this notice. Document Family Hide related notices OCT164307: General Building Maintenance Services Publication Date: 27/10/2016 Deadline: 29/11/2016 Notice Type: 02 Contract Notice Authority name: South Wales Fire and Rescue Service MAY197401: General Building Maintenance Services Publication Date: 04/05/2017 Notice Type: 03 Contract Award Notice - Successful Supplier(s) Authority name: South Wales Fire and Rescue Service Copyright © Sell2Wales Connect with us Email signup Subscribe to our email newsletter Subscribe Call us on 0800 222 9004 Accessibility| Privacy Policy & Cookies| Site map| Terms & Conditions| © Millstream Associates Limited 2017 //