Public tenders for electrical in Saint-robert United States

Find all Electrical tenders in the world.
Finding business opportunities has never been easier.

Results for electrical. Make a new search!

Electrical and Data Wire Install

Department of the Army, U.S. Army Corps of Engineers | Published September 25, 2015  -  Deadline October 2, 2015
cpvs

Scope of Work for Installation of Electrical & Data For Ace It Cubicle 7E19A The following describes the services to be performed for US Army Corps of Engineers District located at 180 Fifth Street East Suite700 St. Paul, MN 55101. All work shall comply with Federal State and Local building codes. Data The Horizontal Cabling Subsystem should be constructed as follows: -Contractor will provide and install one (1) dual port furniture outlet. -The contractor shall run new Category 6A Shielded Plenum Rated - data cable from each port on the outlet to the patch closet. -At same time of running data cables for cubicle outlets the contractor shall run two additional data cables which will be coiled up above ceiling tile leaving 12 feel of extra length for future usage -The cables will be installed from the outlet jack, through contractor provided stub out, along the plenum ceiling area using contractor provided conduit sleeves when needed to the IT Closet 7NE. A horizontal run of approximately 175 feet. - Contractor will follow existing cable trays pathways when present and support the cable with hangers, structural support and cable ties when needed. The Work Location Cabling Subsystem will be constructed as follows: -Contractor will terminate the data cables on Category 6A jacks at the workstation. -Patch cords for the terminals are not included in this proposal. The Equipment Room and Telecommunications Closet Subsystem will be constructed as follows: -The data cable will terminate on the existing RJ45 port patch panel hardware in the IT Closet. Contractor will provide Testing of all wiring and connectors include testing for: -Attenuation, Continuity, Polarity, Reversals, Shorts and Grounds Electrical -Contractor will install electrical service to two existing outlets in furniture system raceway off a current ceiling feed panel located above cubicle 7E19A -Contractor needs to provide copy of driver's license and social security number of personnel conducting the work four business days prior to arrival onsite. Identification information shall be provided Duane Isle 651-290-5226 -For Utilization of building freight elevators, loading dock, and alley access please coordinate 72 hours in advance with Facilities Specialist Duane Isle 651-290-5226

62--Electrical Upgrades to Coles Creek Recreational Area at Carlyle Lake, Carlyle, Illlinois

Department of the Army, U.S. Army Corps of Engineers | Published March 20, 2015
cpvs

Electrical Upgrades to Coles Creek Recreational Area at Carlyle Lake, Carlyle, Illlinois

Electrical Power Test Set (EPTS) Software Upgrade

Department of the Navy, Naval Air Systems Command | Published April 22, 2015  -  Deadline May 7, 2015
cpvs

The Naval Air Systems Command (NAVAIR) intends to solicit and negotiate a Firm Fixed-Price Sole Source order to the Basic Ordering Agreement N00019-11-G-0001 to The Boeing Company to procure an Electrical Power Test Set (EPTS) Software Upgrade in support of Engineering Change Proposal (ECP) 6355R1C2. An EPTS Software Upgrade that is compatible with Windows7 was planned for installation in 2017. PMA-260 is upgrading 31 non-F/A18 Aircraft Engine Component Test Stands (AECTS) with Windows7 currently. These stands currently have Windows 98 software and cannot interface. During the interim the old computers would be retained to support F/A-18 AECTS (31 stands). The supplies and/or services to support the EPTS Software Upgrade may include installation of the software in support of engineering change proposals, training in support of software upgrades and associated technical, financial, and administrative data, with planned deliveries in accordance with the Contract Data Requirements. This acquisition is being pursued on a sole source basis under the statutory authority 10 USC 2304 (C)(1) as implemented by Federal Acquisition Regulation (FAR) 6.302-1, "Only one responsible source and no other supplies or services will satisfy agency requirements." This synopsis is for informational purposes only. Inquiries regarding availability of subcontracting opportunities should be directed to The Boeing Company, P.O. Box 516, St. Louis, MO 63166-0516.

NORMANDY ELECTRICAL

Department of the Army, Army Contracting Command, ECC | Published March 31, 2016  -  Deadline April 18, 2016
cpvs

The requirement is for Electgrical Power Distribution System Service.

Electrical Resistivity Imaging Equipment Specifications

Department of Agriculture, Natural Resources Conservation Service | Published September 22, 2015  -  Deadline September 5, 2014
cpvs

Link To Document

Z--Correct Electrical FCA Deficiencies

Department of Veterans Affairs, Columbus VAOPC | Published March 16, 2015  -  Deadline July 23, 2015
cpvs

No Description Provided

Z--MAINT SHOP MOVE ELECTRIC METER BASE

Department of the Interior, Fish and Wildlife Service | Published August 24, 2016  -  Deadline September 2, 2016
cpvs

IGF::OT::IGF The Contractor shall provide all labor, equipment, tools, materials, transportation and incidental items to move electrical meter base.

Furnish Electric Lights & Fans Installation at Range 33

Department of the Army, Army Contracting Command, MICC | Published May 25, 2016
cpvs

This acquisition is being solicited as a HUBzone Small Business Set-Aside. The NAICS code is 238210 with a size standard of $15.0M. The Mission and Installation Contracting Command, Installation Contracting Office, Fort Leonard Wood, Missouri has a requirement Furnish Electrical Lights and Fans installation at Range 33 Training Complex at Fort Leonard Wood. The contractor shall provide all plant, labor, equipment, supplies and materials, and performing all work in accordance with specifications and provided drawings to perform this requirement at Fort Leonard Wood, Missouri. The areas concerned in this project are government owned. They will be in use during the progress of the work and the contractor shall arrange their operations to cause as little interference as possible; work shall be performed during normal duty hours identified as 7:30 a.m. to 4:00 p.m., Monday through Friday, legal public holidays excepted.. All work performed shall be in accordance with the manufacturers specifications. The magnitude of this project is between $100,000 and $250,000. This will be a fixed price construction contract. The solicitation W911S7-16-B-0013 will be available on or about 8 June 2016 on the Federal Business Opportunities (FBO) website (http://www.fbo.gov). For information on how to register your company on FBO, to view or receive updates and notifications to the solicitation, please reference the FBO Vendor Guide located on the FBO web site home page. NO paper copies of the solicitation will be furnished. A solicitation mailing list will not be maintained for this procurement. Inquiries will only be addressed by EMAIL ONLY. Forward any questions to david.w.foster24.civ@mail.mil THE SOLICITATION AND ANY AMENDMENTS ARE PAPERLESS AND WILL BE AVAILABLE ON THE INTERNET ONLY. **NOTE: Prior to submission of an offer, Contractors must be actively registered and have an active FAR and DFARS certification in the System for Award Management (SAM) in order to receive a contract award from any DoD agency. Contractors may access the Internet site at: https://www.sam.gov/ to register and/or obtain information about the SAM program. FAR and DFARS Representations and Certifications can be submitted at https://www.sam.gov/.

Various Electrical Adapters for Cable Assemblies

Department of the Navy, Naval Air Systems Command | Published April 5, 2016  -  Deadline April 12, 2016
cpvs

  Solicitation N00421-16-T-0233 is issued as a brand name procurement. This action will be conducted under Federal Acquisition Regulation (FAR) Part 12 and FAR Part 13.   The Government intends to purchase on a firm fixed-price basis, and to solicit and award the proposed purchase order on a brand name basis, for Glenair Parts, under the authority implemented by Federal Acquisition Regulation (FAR) Part 13.106-1(b).  All responding vendors must be registered in the System for Award Management (SAM) Database prior to submission of an offer to be considered for award of any DoD contract.  This may be accomplished electronically at http://www.sam.gov/vendor.cfm.  The Government intends to award this on a brand name basis. All interested parties MUST submit a brand name quote no later than 4:00pm Eastern Standard Time, 12-APR-2016. The Government will consider quotes from all responsible sources with the capability to provide the Brand Name products cited. Preference will be given to quotes from small businesses. Vendor must be an authorized distributor / authorized reseller; Items must be covered under the Manufacturer's Warranty; Used or refurbished items will not be accepted.  Award will be made on an all or none basis.  All quotes/responses shall be submitted via email to Olive Rogers at olive.rogers@navy.mil

Z--Electrical Upgrade at Building 1407 LOX (Liquid Oxygen) Storage

Department of the Army, National Guard Bureau | Published August 25, 2015  -  Deadline September 10, 2015
cpvs

Synopsis not required IAW FAR 5.202(a)(13). See solicitation.

Y--Replace Exterior Electrical Transformers Bldg. 13 Project: 539-16-504

Department of Veterans Affairs, Dayton VAMC | Published July 7, 2016
cpvs

No Description Provided

65-- COMBINED SYNOPSIS SOLICITATION W91YU0-15-T-0099 - AQUARIUS CT URODYNAMIC ANALYZER

Department of the Army, U.S. Army Medical Command | Published February 18, 2015  -  Deadline March 6, 2015
cpvs

THIS IS A COMBINED SYNOPSIS/SOLICITATION FOR COMMERCIAL ITEMS PREPARED IN ACCORDANCE WITH THE FORMAT IN FAR SUBPART 12.6-STREAMLINED PROCEDURES FOR EVALUATION AND SOLICITATION FOR COMMERCIAL ITEMS-AS SUPPLEMENTED WITH ADDITIONAL INFORMATION INCLUDED IN THIS NOTICE, THIS ANNOUNCEMENT CONSTITUTES THE ONLY SOLICITATION. OFFERS ARE BEING REQUESTED, AND A WRITTEN SOLICITATION DOCUMENT WILL NOT BE ISSUED. This is a solicitation W91YU0-15-T-0099 of Purchase Request 0010640219 is issued as a Request for Quotation (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular (FAC) 2005-78. The associated North American Industrial Classification System (NAICS) code for this procurement is 423450; Size Standard for small business is 500 employees. RFQ is being issued as UNRESTRICTED. This requirement is for Urodynamic Analyzer to be used at General Leonard Wood Army Community Hospital, 126 Missouri Ave; FT Leonard Wood MO. 65473. All responsible Contractors shall provide an offer for the following Brand Name or Equal Products: LINE ITEM 0001: 01 EA; Part# CAR1030 Aquarius CT Urodynamic System, with Single LCD, Cart LINE ITEM 0002: 01 EA; FREIGHT / SHIPPING System Specifications: AQUARIUS Carts L = 29.8 quote mark (75.7cm) W = 25.2 quote mark (64.0cm) H = 49.2 quote mark (125.0cm) Operating Conditions Temperatures: 15 C to 35 C (59 F to 95 F) Humidity: 30% to 75% relative humidity (non-condensing) Pressure: 700 hPa to 1014hPa Transport and Storage Conditions Temperature: -10 C to 50 C (14 F to 122 F) Humidity: 20% to 80% relative humidity (non-condensing) Pressure: 700hPa to 1014hPa Pump Hub P/N: PMP1000 Output Channels: 2 Infusion / 1 Bubble/1 USB type A/ 1 USB type B RoamDX P/N: RMX1000 Dimensions: 5.5 quote mark (14cm) L X 3.6 quote mark (9.3cm) W X 1.6 quote mark (3.9) H Weight: 0.60 lbs (0.27kg) Pressure Range: -50 to +350 cmH20; EMG Range: 0 to 1000uV Output Channels: 4 Pressure / 1 EMG / 1 Pressure/EMG Sampling Rate (each channel): Pressure= 50Hz max.; EMG=5000Hz max. / 10 - 100 Hz (increments of 10Hz) Urocap V P/N: TRA1002 Dimensions: 6.3 quote mark (16.0cm) L X 6.3 quote mark (16.0cm) W X 2.6 quote mark (6.6cm) H Weight: 0.95lbs (0.43kg) Flow Range: 0 to 50mL/s; Volume Range: 0 to 1000mL Output Channels: Flow; Volume Sampling Rate: Flow=100Hz max.; Volume=100Hz max. UPX (arm and stand) P/N: UPP1001 Dimensions: 23.5 quote mark (59.7cm) L X 23.5 quote mark (59.7cm) W X 35.6 quote mark (90.4cm) H / arm extension : 30 (76cm) Luxo: Extension 36.0 quote mark (91.5cm) / Weight: 3.3 lbs. (1.5kg) Speed: 0 to 3 mm/s AQUARIUS CT CART - SINGLE DISPLAY L = 36 quote mark (90.0cm) W = 26 quote mark (66.0cm) H = 48 quote mark (120.0cm) DUAL DISPLAY L = 36 quote mark (90.0cm) W = 34.5 quote mark (88.0cm)* H = 48 quote mark (120.0cm) *operational width described - can pivot to pass through doors. AQUARIUS XT TOWER L = 24 quote mark (60.0cm) W = 26 quote mark (66.0cm) H = 48 quote mark (120.0cm) AQUARIUS XT PC CART - SINGLE DISPLAY L = 36 quote mark (90.0cm) W = 26 quote mark (66.0cm) H = 48 quote mark (120.0cm) DUAL DISPLAY L = 36 quote mark (90.0cm) W = 34.5 quote mark (88.0cm)* H = 48 quote mark (120.0cm) *operational width described - can pivot to pass through doors. AQUARIUS LT L = 32 quote mark (81.0cm) W = 26 quote mark (66.0cm) H = 48 quote mark (120.0cm) AQUARIUS CTS L = 36 quote mark (90.0cm) W = 26 quote mark (66.0cm) H = 48 quote mark (120.0cm) T-DOC Air-Charged Catheters Operating conditions: 15 C (59 F) to 40 C (104 F) Storage Temperature: -25 C (-13 F) to +50 C (122 F) AQUARIUS XT/CT/LT/CTS Owner's Manual II CLASSIFICATIONS AND APPLICABLE DIRECTIVES Classifications Class I Type BF Applied Part Mode of Operation Continuous Equipment not suitable for use in the presence of a Flammable Anesthetic Mixture with Air, or Oxygen or Nitrous Oxide. Applicable Directives and Standards Directives: Food and Drug Administration Code of Federal Regulations 21 CFR 820 quote mark Quality System Regulation. quote mark European Medical Devices Directive 93/42/EEC SOR/98-282 Health Canada Medical Device Regulations Standards: EN ISO 13485:2012 (EU) ISO 13485:2003 CAN/CSA ISO 13485:2003 (Canada) EN ISO 14971:2012 EN 60601-1:2006 EN 60601-1-2:2007 EN 60601-1-6:2010 EN 62304:2006 EN 62366:2008 EN ISO 15223-1:2012 EN ISO 7010:2012 EN 1041:2008 UL 60601-1:2003, excluding electromagnetic compatibility (Clauses 6.8.2 and 36), and Biocompatibility (Clause 48) and Programmable Electronic Systems (Clause 52.1) CAN/CSA C22.2 No. 601.1-M90, excluding electromagnetic compatibility (Clauses 6.8.2 and 36), and Biocompatibility (Clause 48) and Programmable Electronic Systems (Clause 52.1) CAN/CSA C22.2 No. 60601-1:2008, excluding Usability (clauses 7.1.1 and 12.2), Electromagnetic Compatibility (clauses 7.9.2.2 and 17) Programmable Electrical Medical Systems (clause 14), and Biocompatibility (clause 11.7) ANSI/AAMI ES 60601-1:2005/A2:2010, excluding Usability (clauses 7.1.1 and 12.2), Electromagnetic Compatibility (clauses 7.9.2.2 and 17) Programmable Electrical Medical Systems (clause 14), and Biocompatibility (clause 11.7) TYPE BF APPLIED PARTS EMG/CMG Pressure transducers Delivery shall be FOB Destination to General Leonard Wood MO. Pricing quote shall include all applicable fees. The full text of a FAR provision or clause may be accessed electronically at: www.farsite.hill.af.mil The following clauses apply to this acquisition: 52.212-4 Contract Terms and Conditions-Commercial Items. Addendum to 52.212-4 (LOCAL Clause 5003) Wide Area Workflow (WAWF) Army Electronic Invoicing Instructions, 52.222-3 Convict Labor, 52.222-19 Child Labor-Cooperation With Authorities And Remedies, 52.222-21, Prohibition of Segregated Facilities, 52-222-26 Equal Opportunity, 52.222-35 Equal Opportunity for Special Disabled Veterans, 52.222-36 Affirmative Action for Workers with Disabilities, 52.222-37 Employment Reports on Special Disabled Veterans, Veterans of the Vietnam Era, and Other eligible Veterans, 52.222-50 Combating Trafficking in Persons, 52.223-18 Encouraging Contractor Policies to BanText Messaging While Driving, 52.225-13 Restriction on Certain Foreign Purchases, 52.232-18, Availability of Funds, 52.225-13 Restrictions on Certain Foreign Purchases, 52.233-3 Protest After Award, and 52.233-4, Applicable Law for Breach of Contract Claim, 52.242-13 Bankruptcy, 252.203-7000 Requirements relating to Compensation of Former DoD Employees and 252.203-7002 Requirement to Inform Employees of Whistleblower Rights, 252.204-7003 Control of Government Personnel Work Product, 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports, 252.232-7010 Levies on Contract Payments, 252.225-7036 Buy American -Free Trade Agreements- Balance of Payments Program, 252.247-7023 Transportation of Supplies by Sea. 52.252-2 Clauses Incorporated by Reference, 52.252-6 Authorized Deviations in Clauses, 52.212-5 Contract Terms and Conditions Required to Implement Statutes or Executive Order (Commercial Items-Deviation).52.217-9 Option to Extend the Term of the Contract, 52.211-6 Brand Name or Equal, 52.252-6 Authorized Deviation in Clauses, The following provision apply to this acquisition. 52.212-1 Instructions to Offerors-Commerical Items, Addendum to 52.212-1, 52.252-1 Solicitation Provision Incorporated by Reference, 52.252-5 Authorized Deviations in Provisions, 52.225-25 Prohibition on Engaging in Sanctioned Activities relating to Iran-Certification, 252.203-7005 Representation relating to Compensation of Former DoD Officials. Potential contractors must be registered in the System for Award Management (SAM) to be eligible for award. The SAM internet web site is http://www.sam.gov. Offers are due by 06 March 2015, 12:00 PM, Pacific Standard Time. Submit offers via fax to (360) 360-0787 or email walter.j.bischoff.civ@mail.mil . All submitted offers by fax or email must be dated and signed by the offeror or they will not be considered. Place of performance: General Leonard Wood Army Community Hospital 126 Missouri Ave Fort Leonard Wood MO 65473 UNITED STATES

USDC Clerks Kitchen Renovation

General Services Administration, Public Buildings Service (PBS) | Published April 24, 2015  -  Deadline May 12, 2015
cpvs

Renovation of the clerk's 1st floor kitchenette area. The total project includes, but is not limited to, removing existing kitchen cabinetry, installation of new kitchen cabinets, countertops, sinks, faucet, garbage disposal, under cabinet lighting and related electrical outlets. Existing carpeting will be replaced with hard flooring in areas and painting is to be performed.

DPW Washer & Dryers

Department of the Army, Army Contracting Command, MICC | Published October 9, 2015  -  Deadline October 20, 2015
cpvs

W911S7-16-R-0001 DPW Washers & Dryers This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in the Federal Acquisition Regulation (FAR) Subpart 12.6 as supplemented with additional information included in this notice. This announcement constitutes the only solicitation. Quotes are being requested for the required items and no written solicitation will be issued. Solicitation number W911S7-16-R-0001 is issued as a Request for Quotes. This solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2005-43 dated 02 August 2010. This is procurement is a Total Small Business set-aside for Small Business under NAICS 333318 with a size standard of 1,000 Employees. Ft. Leonard Wood, MO requires the following items. CLIN 0001- New Purchase - Qty. 482 Washers and Qty. 483 Dryers. FOB: Destination - Fort Leonard Wood MO 65473. Description and Specification Requirements: NOTE: All equipment, including all required ancillary equipment, provided shall be NEW "OUT OF THE BOX", never before installed or operated, and shall have been manufactured within the past two (2) years. Machines shall be white in color. At the start of the contract period, the Contractor shall provide the Contracting Officer with a letter certifying that, subject to that penalty provisions of 18 U.S.C. Section 1001, all equipment is new and unused, as defined in this paragraph. WASHER MACHINES: Washer machines shall conform to the following salient characteristics. Equipment shall be commercial grade (defined as a washer machine such as used in commercial laundry centers where the expectation is that the machine will be used all day, every day as opposed to occasional use of a residential use machine), self-service and automatic (fully automated, electrical appliance that controls all aspects of clothes washing, from water level and temperature to agitation time and intensity, operated by the end user by deposit of clothing into the machine, selection of machine setting, and not requiring assistance of a laundry attendant), shall have minimum of three wash temperatures and a cold rinse temperature, and shall have a tub capacity in the range of 2.7 cubic feet to 3.3 cubic feet. Machines shall not be coin-operated. Machines must also comply with the minimum energy efficiency requirements of FAR 52.223-15 which is incorporated into the contract. Washer machine shall be 110 Volt receptacle. Installer to verify connection prior to installation. Contractor shall provide specifications of the proposed equipment with proposal submission. DRYER MACHINES: Dryer machines shall conform to the following salient characteristics. Equipment shall be tumbler-type, shall have a Permanent Press setting with adjustable heat settings and be commercial grade (defined as a dryer machine such as used in commercial laundry centers where the expectation is that the machine will be used all day, every day every day as opposed to occasional use of a residential use machine), self-service and automatic (fully automated, electrical appliance that controls all aspects of clothes drying, from drying temperature to drying time, operated by the end user by deposit of clothing into the machine, selection of machine setting, and not requiring assistance of a laundry attendant), electric heating, 240 volt, 60 Hz single phase AC, and have a cylinder capacity in the range of from 5.5 cubic feet to 7.0 cubic feet. Machines shall not be coin-operated. Machines must also comply with minimum energy efficiency requirements of FAR 52.223-15 which is incorporated into the contract. Dryer machines will have the possibility of 3 or 4 prong connection. Installer to verify connection prior to installation. Contractor shall provide specifications of the proposed equipment with proposal submission. WARRANTY: Washer machines and dryer machines shall be provided with 1-year manufacturer warranty on parts and labor. Warranty shall be provided at the time of installation. INSTALLATION: The Contractor shall deliver and install washing machines and dryer machines at locations within buildings specified by the Government. Locations are centralized on each floor, no elevators are provided at these locations. The Contractor shall provide all necessary electrical wires and plugs, plumbing fixtures, venting devices, and other necessary fixtures extending from the washer machines and dryer machines, to affect safe and efficient hookups with the building electrical outlets, drainage pipes, and vents. All expenses associated with installation of washers and dryers to include labor, materials and equipment must be included in the prices quoted for washers and dryers. No other payment will be made. Installation shall be in accordance with standard commercial practices. Contractor shall coordinate with the incumbent contractor to affect an orderly and expeditious transition. The incumbent contractor will remove their leased washer machines and dryer machines and contractor shall replace on a one-to-one basis. DPW will provide a schedule for removal and replacement, in which the incumbent will remove all equipment from each location, and the awarded contractor shall immediately install their equipment in each vacated location in order to avoid a lapse in service. The phase-in period will not exceed 60-calendar days; the average number of unit sets to be replaced per week is an average of 60 unit sets (unit set defined as one washer machine and one dryer machine) per week. No storage is available during the duration of this project. SEE ATTACHMENT TE 1- Locations Washer Machines and Dryer Machines to be installed. IDENTIFICATION NUMBERS: The Contractor shall provide documents that include serial number and location of washer machines and dryer machines after installation. QUOTES Quotes are due no later than 2:00 p.m. Central Daylight Time on Tuesday October 20, 2015. Quotes shall include a unit total, line item total, and technical specifications for the quoted Washer Machines and a unit total, line item total, and technical specifications for the quoted Dryer Machines. Quotes provided shall be inclusive of equipment, ancillary equipment and supplies, shipping, delivery and transportation costs and complete installation. Quotes shall be submitted via e-mail to david.w.foster24.civ@mail.mil or via USPS or commercial delivery service to: MICC-ICO Ft. Leonard Wood, ATTN: David Foster; 5772 Iowa Avenue., Ft. Leonard Wood MO 65473. All quotes shall reference solicitation number W911S7-16-R-0001 in the subject line. The point of contact for this solicitation is David W. Foster, Contract Specialist; phone (573) 596-0246. QUESTIONS Questions regarding this solicitation shall be submitted in writing via e-mail to David Foster, Contract Specialist, at david.w.foster24.civ@mail.mil no later than Wednesday October 14, 2015 at 3:00 pm (Central Standard Time). The following Federal Acquisition Regulation (FAR) and Defense Federal Acquisition Regulation Supplement (DFARS) provisions and clauses are applicable and are incorporated by reference: 52.204-7 System of Award Management JUL 2013 52.212-1 Instructions to Offerors-Commercial Items APR 2014 52.212-4 Contract Terms and Conditions-Commercial Items MAY 2014 52.246-2 Inspection of Supplies (Fixed Price) AUG 1966 252.203-7002 Requirements to Inform Employees of Whistleblower Rights SEP 2013 252.204-7003 Control of Government Personnel Work Product APR 1992 252.204-7006 Billing Instructions OCT 2005 252.211-7003 Item Unique Identification and Valuation DEC 2013 252.232-7003 Electronic Submission of Payment Requests and JUNE 2012 Receiving Reports 252.232-7010 Levies on Contract Payments DEC 2006 252.243-7002 Request for Equitable Adjustment CLAUSES INCORPORATED BY FULL TEXT 52.212-2 EVALUATION--COMMERCIAL ITEMS ADDENDUM TO FAR 52.212-2 EVALUATION-COMMERCIAL ITEMS EVALUATION FACTORS FOR AWARD Basis for Contract Award This is a Lowest Price Technically Acceptable (LPTA) best value source selection conducted in accordance with Federal Acquisition Regulation (FAR) 15.3, Source Selection, as supplemented by the Defense Federal Acquisition Regulation Supplement (DFARS), and the Army Federal Acquisition Regulation Supplement (AFARS). Award will be made to a single offeror who is deemed responsible in accordance with the Federal Acquisition Regulation (FAR), whose proposal conforms to the solicitation requirements, and whose proposal, judged by an overall assessment of the evaluation criteria and other considerations specified in this solicitation, represents the Lowest Priced Technically Acceptable offer. Trade-offs between cost/price and non-cost/price factors are not permitted. Unreasonably high/unrealistically low, unbalanced, inaccurate or incomplete price proposals may be grounds for eliminating a proposal from competition. The Government will evaluate proposed prices for reasonableness and balance by utilizing price analysis techniques. Proposed prices evaluated as unreasonable may be grounds for eliminating a proposal from competition. The Government intends to award one (1) contract as a result of this solicitation. As set forth in FAR 52.215-1 (f)(4), the Government intends to evaluate proposals and technical specifications and award a contract without discussions with offerors (except clarifications as described in FAR 15.306(a), Clarifications and award without discussions). Therefore, the offeror's initial proposal should contain the offeror's best terms from a cost or price and technical specifications. EVALUATION CRITERIA: The evaluation criteria consists of factors. The proposals will be evaluated under two (2) evaluation factors: FACTOR 1: Technical Acceptability of submitted specifications in accordance with salient characteristics of equipment FACTOR 2: Price A. EVALUATION APPROACH: Factor 1--Technical Acceptability: The technical proposal must consist of the technical specifications for the washing machines and dryers supported by any additional information in sufficient detail to establish that the machines offered fully comply with the salient characteristics contained in PWS paragraphs Washer Machines and Dryer Machines. Likewise the technical proposal should confirm that offered machines are new out of the box and manufactured within the past two years. If the technical specifications provided do not address the warranty requirement Offerors shall confirm that offered machines will have a warranty meeting the requirements detailed in the PWS section entitled Warranty. The Technical Acceptability evaluation provides an assessment of the offeror's submitted specifications on equipment proposed to satisfy the Government's requirement. The evaluation will focus on whether the offeror's proposal meets or does not meet the Government's requirements. The technical acceptability factor will receive one of the adjectival ratings defined below. Offerors must receive an "Acceptable" rating for the Technical Acceptability factor in order to be considered for award. Technical Evaluation Ratings ADJECTIVAL RATING DESCRIPTION Acceptable The equipment offered and terms clearly meet the minimum requirements of the solicitation. Unacceptable The equipment offered and terms do not clearly meet the minimum requirements of the solicitation. Factor 2--Price: Price will not be scored or rated. Evaluation of price will be performed using one or more of the price analysis techniques in FAR 15.404-1(b). Through these techniques, the Government will determine whether prices are reasonable, complete, and balanced. Unbalanced pricing may be evaluated in accordance with FAR 15.404-1(g), as applicable, to assess potential performance risk which could result in unreasonably high prices. Definitions: Reasonableness: A price is reasonable if, in its nature and amount, it does not exceed that which would be incurred by a prudent person in the conduct of competitive business. (FAR 31.201-3) Unbalanced Pricing: Pricing that exists when, despite an acceptable total evaluated price, the price of one or more contract line item is significantly over/under stated as indicated by the application of cost or price analysis techniques. (FAR 15.404-1(g)) B. EVALUATION PROCEDURES: The technical evaluator(s) shall assess each technical proposal submitted for "ACCEPTABILITY". Proposals that are determined to be UNACCEPTABLE upon technical evaluation will be rejected. Failure to achieve a rating of Acceptable will result in an "Unacceptable" determination for the Technical Proposal. An "Unacceptable" rating results in elimination from further award consideration. Award will be made to the lowest price technically acceptable offer unless the price is so low as to be unreasonable. The Government may determine that a proposal is unacceptable if the price offered is so low that it is determined that the offeror cannot accomplish the level of services promised in the technical proposal for the prices offered in the cost proposal. The Government will not award a contract at a price so low that it will create a likelihood that the offeror will fail to provide a satisfactory level of performance. Offerors offering unique cost saving initiatives should fully explain their cost methodology to substantiate their ability to perform at the prices offered. (b) A written notice of award or acceptance of an offer, mailed or otherwise furnished to the successful offeror within the time for acceptance specified in the offer, shall result in a binding contract without further action by either party. Before the offer's specified expiration time, the Government may accept an offer (or part of an offer), whether or not there are negotiations after its receipt, unless a written notice of withdrawal is received before award. (End of provision) 52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR EXECUTIVE ORDERS--COMMERCIAL ITEMS (MAY 2015) (a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses, which are incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to acquisitions of commercial items: (1) 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (Dec 2014) (2) 52.233-3, Protest After Award (AUG 1996) (31 U.S.C. 3553). (3) 52.233-4, Applicable Law for Breach of Contract Claim (OCT 2004) (Public Laws 108-77 and 108-78 (19 U.S.C. 3805 note)). (b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial items: (Contracting Officer check as appropriate.) X (1) 52.203-6, Restrictions on Subcontractor Sales to the Government (Sept 2006), with Alternate I (Oct 1995) (41 U.S.C. 4704 and 10 U.S.C. 2402). X(2) 52.203-13, Contractor Code of Business Ethics and Conduct (Apr 2010) (41 U.S.C. 3509). X (3) 52.203-15, Whistleblower Protections under the American Recovery and Reinvestment Act of 2009 (June 2010) (Section 1553 of Pub. L. 111-5). (Applies to contracts funded by the American Recovery and Reinvestment Act of 2009.) ____(4) 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards (July 2013) (Pub. L. 109- 282) (31 U.S.C. 6101 note). (5) [Reserved] (6) 52.204-14, Service Contract Reporting Requirements (JAN 2014) (Pub. L. 111-117, section 743 of Div. C). (7) 52.204-15, Service Contract Reporting Requirements for Indefinite-Delivery Contracts (JAN 2014) (Pub. L. 111-117, section 743 of Div. C). X (8) 52.209-6, Protecting the Government's Interest When Subcontracting with Contractors Debarred, Suspended, or Proposed for Debarment. (Aug, 2013) (31 U.S.C. 6101 note). (9) 52.209-9, Updates of Publicly Available Information Regarding Responsibility Matters (July 2013) (41 U.S.C. 2313). (10) [Reserved] (11)(i) 52.219-3, Notice of HUBZone Set-Aside or Sole-Source Award (NOV 2011) (15 U.S.C. 657a). _ (ii) Alternate I (NOV 2011) of 52.219-3. (12) (i) 52.219-4, Notice of Price Evaluation Preference for HUBZone Small Business Concerns (OCT 2014) (if the offeror elects to waive the preference, it shall so indicate in its offer) (15 U.S.C. 657a). (ii) Alternate I (JAN 2011) of 52.219-4. (13) [Reserved] X (14)(i) 52.219-6, Notice of Total Small Business Set-Aside (NOV 2011) (15 U.S.C. 644). (ii) Alternate I (NOV 2011). (iii) Alternate II (NOV 2011). (15)(i) 52.219-7, Notice of Partial Small Business Set-Aside (June 2003) (15 U.S.C. 644). (ii) Alternate I (Oct 1995) of 52.219-7. (iii) Alternate II (Mar 2004) of 52.219-7. X (16) 52.219-8, Utilization of Small Business Concerns (OCT 2014) (15 U.S.C. 637(d)(2) and (3)). (17)(i) 52.219-9, Small Business Subcontracting Plan (OCT 2014) (15 U.S.C. 637(d)(4)). (ii) Alternate I (Oct 2001) of 52.219-9. (iii) Alternate II (Oct 2001) of 52.219-9. (iv) Alternate III (OCT 2014) of 52.219-9. (18) 52.219-13, Notice of Set-Aside of Orders (NOV 2011) (15 U.S.C. 644(r)). X (19) 52.219-14, Limitations on Subcontracting (NOV 2011) (15 U.S.C. 637(a)(14)). (20) 52.219-16, Liquidated Damages-Subcon-tracting Plan (Jan 1999) (15 U.S.C. 637(d)(4)(F)(i)). (21) 52.219-27, Notice of Service-Disabled Veteran-Owned Small Business Set-Aside (NOV 2011) (15 U.S.C. 657f). X (22) 52.219-28, Post Award Small Business Program Rerepresentation (July 2013) (15 U.S.C. 632(a)(2)). (23) 52.219-29, Notice of Set-Aside for Economically Disadvantaged Women-Owned Small Business (EDWOSB) Concerns (July 2013) (15 U.S.C. 637(m)). (24) 52.219-30, Notice of Set-Aside for Women-Owned Small Business (WOSB) Concerns Eligible Under the WOSB Program (July 2013) (15 U.S.C. 637(m)). X (25) 52.222-3, Convict Labor (June 2003) (E.O. 11755). X (26) 52.222-19, Child Labor-Cooperation with Authorities and Remedies (JAN 2014) (E.O. 3126). X (27) 52.222-21, Prohibition of Segregated Facilities (Apr 2015). X (28) 52.222-26, Equal Opportunity (Apr 2015) (E.O. 11246). X (29) 52.222-35, Equal Opportunity for Veterans (Jul 2014)(38 U.S.C. 4212). X (30) 52.222-36, Equal Opportunity for Workers with Disabilities (July 2014) (29 U.S.C. 793). X (31) 52.222-37, Employment Reports on Veterans (July 2014) (38 U.S.C. 4212). (32) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O. 13496). X (33)(i) 52.222-50, Combating Trafficking in Persons (March 2, 2015) (22 U.S.C. chapter 78 and E.O. 13627). (ii) Alternate I (March 2, 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627). X (34) 52.222-54, Employment Eligibility Verification (Aug 2013). (Executive Order 12989). (Not applicable to the acquisition of commercially available off-the-shelf items or certain other types of commercial items as prescribed in 22.1803.) (35)(i) 52.223-9, Estimate of Percentage of Recovered Material Content for EPA-Designated Items (May 2008) (42 U.S.C. 6962(c)(3)(A)(ii)). (Not applicable to the acquisition of commercially available off-the-shelf items.) (ii) Alternate I (May 2008) of 52.223-9 (42 U.S.C. 6962(i)(2)(C)). (Not applicable to the acquisition of commercially available off-the-shelf items.) (36) (i) 52.223-13, Acquisition of EPEAT® Registered Imaging Equipment (Jun 2014) (E.O.s 13423 and 13514). (ii) Alternate I (Jun 2014) of 52.223-13. (37)(i) 52.223-14, Acquisition of EPEAT® Registered Televisions (Jun 2014) (E.O.s 13423 and 13514). (ii) Alternate I (Jun 2014) of 52.223-14. X (38) 52.223-15, Energy Efficiency in Energy-Consuming Products (Dec 2007) (42 U.S.C. 8259b). (39)(i) (i) 52.223-16, Acquisition of EPEAT® -Registered Personal Computer Products (Jun 2014) (E.O.s 13423 and 13514). (ii) Alternate I (Jun 2014) of 52.223-16. X (40) 52.223-18, Encouraging Contractor Policies to Ban Text Messaging While Driving (Aug 2011) (E.O. 13513). X (41) 52.225-1, Buy American--Supplies (May 2014) (41 U.S.C. chapter 83). (42) (i) 52.225-3, Buy American--Free Trade Agreements--Israeli Trade Act (May 2014) (41 U.S.C. chapter 83, 19 U.S.C. 3301 note, 19 U.S.C. 2112 note, 19 U.S.C. 3805 note, 19 U.S.C. 4001 note, Pub. L. 103-182, 108-77, 108-78, 108-286, 108-302, 109-53, 109-169, 109-283, 110-138, 112-41, 112-42, and 112-43. (ii) Alternate I (May 2014) of 52.225-3. (iii) Alternate II (May 2014) of 52.225-3. (iv) Alternate III (May 2014) of 52.225-3. (43) 52.225-5, Trade Agreements (Nov 2013) (19 U.S.C. 2501, et seq., 19 U.S.C. 3301 note). ___(44) 52.225-13, Restrictions on Certain Foreign Purchases (June 2008) (E.O.'s, proclamations, and statutes administered by the Office of Foreign Assets Control of the Department of the Treasury). (45) 52.225-26, Contractors Performing Private Security Functions Outside the United States (Jul 2013) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. 2302 Note). (46) 52.226-4, Notice of Disaster or Emergency Area Set-Aside (Nov 2007) (42 U.S.C. 5150 (47) 52.226-5, Restrictions on Subcontracting Outside Disaster or Emergency Area (Nov 2007) (42 U.S.C. 5150). (48) 52.232-29, Terms for Financing of Purchases of Commercial Items (Feb 2002) (41 U.S.C. 4505, 10 U.S.C. 2307(f)). (49) 52.232-30, Installment Payments for Commercial Items (Oct 1995) (41 U.S.C. 4505, 10 U.S.C. 2307(f)). X(50) 52.232-33, Payment by Electronic Funds Transfer-System for Award Management (July 2013) (31 U.S.C. 3332). (51) 52.232-34, Payment by Electronic Funds Transfer-Other than System for Award Management (July 2013) (31 U.S.C. 3332). (52) 52.232-36, Payment by Third Party (MAY 2014) (31 U.S.C. 3332). (53) 52.239-1, Privacy or Security Safeguards (Aug 1996) (5 U.S.C. 552a). (54)(i) 52.247-64, Preference for Privately Owned U.S.-Flag Commercial Vessels (Feb 2006) (46 U.S.C. Appx. 1241(b) and 10 U.S.C. 2631). (ii) Alternate I (Apr 2003) of 52.247-64. (c) The Contractor shall comply with the FAR clauses in this paragraph (c), applicable to commercial services, that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial items: (Contracting Officer check as appropriate.) X(1) 52.222-17, Nondisplacement of Qualified Workers (May 2014) (E.O. 13495). __ (2) 52.222-41, Service Contract Labor Standards (MAY 2014) (41 U.S.C. chapter 67). (3) 52.222-42, Statement of Equivalent Rates for Federal Hires (MAY 2014) (29 U.S.C. 206 and 41 U.S.C. chapter 67). ___ (4) 52.222-43, Fair Labor Standards Act and Service Contract Labor Standards--Price Adjustment (Multiple Year and Option Contracts) (MAY 2014) (29 U.S.C. 206 and 41 U.S.C. chapter 67). (5) 52.222-44, Fair Labor Standards Act and Service Contract Labor Standards--Price Adjustment (MAY 2014) (29 U.S.C 206 and 41 U.S.C. chapter 67). (6) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for Maintenance, Calibration, or Repair of Certain Equipment--Requirements (MAY 2014) (41 U.S.C. chapter 67). (7) 52.222-53, Exemption from Application of the Service Contract Labor Standards to Contracts for Certain Services--Requirements (MAY 2014) (41 U.S.C. chapter 67). X (8) 52.222-55, Minimum Wages Under Executive Order 13658 (Dec 2014) (E.O. 13658). ` (9) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations (MAY 2014) (42 U.S.C. 1792). (10) 52.237-11, Accepting and Dispensing of $1 Coin (Sept 2008) (31 U.S.C. 5112(p)(1)). (d) Comptroller General Examination of Record. The Contractor shall comply with the provisions of this paragraph (d) if this contract was awarded using other than sealed bid, is in excess of the simplified acquisition threshold, and does not contain the clause at 52.215-2, Audit and Records--Negotiation. (1) The Comptroller General of the United States, or an authorized representative of the Comptroller General, shall have access to and right to examine any of the Contractor's directly pertinent records involving transactions related to this contract. (2) The Contractor shall make available at its offices at all reasonable times the records, materials, and other evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any shorter period specified in FAR Subpart 4.7, Contractor Records Retention, of the other clauses of this contract. If this contract is completely or partially terminated, the records relating to the work terminated shall be made available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available until such appeals, litigation, or claims are finally resolved. (3) As used in this clause, records include books, documents, accounting procedures and practices, and other data, regardless of type and regardless of form. This does not require the Contractor to create or maintain any record that the Contractor does not maintain in the ordinary course of business or pursuant to a provision of law. (e) (1) Notwithstanding the requirements of the clauses in paragraphs (a), (b), (c), and (d) of this clause, the Contractor is not required to flow down any FAR clause, other than those in this paragraph (e)(1)in a subcontract for commercial items. Unless otherwise indicated below, the extent of the flow down shall be as required by the clause- (i) 52.203-13, Contractor Code of Business Ethics and Conduct (APR 2010) (41 U.S.C. 3509). (ii) 52.219-8, Utilization of Small Business Concerns (OCT 2014) (15 U.S.C. 637(d)(2) and (3)), in all subcontracts that offer further subcontracting opportunities. If the subcontract (except subcontracts to small business concerns) exceeds $650,000 ($1.5 million for construction of any public facility), the subcontractor must include 52.219-8 in lower tier subcontracts that offer subcontracting opportunities. (iii) 52.222-17, Nondisplacement of Qualified Workers (MAY 2014) (E.O. 13495). Flow down required in accordance with paragraph (l) of FAR clause 52.222-17. (iv) 52.222-21, Prohibition of Segregated Facilities (Apr 2015). (v) 52.222-26, Equal Opportunity (APR 2015) (E.O. 11246). (vi) 52.222-35, Equal Opportunity for Veterans (JUL 2014) (38 U.S.C. 4212). (vii) 52.222-36, Equal Opportunity for Workers with Disabilities (Jul 2014) (29 U.S.C. 793). (viii) 52.222-37, Employment Reports on Veterans (Jul 2014) (38 U.S.C. 4212). (ix) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O. 13496). Flow down required in accordance with paragraph (f) of FAR clause 52.222-40. (x) 52.222-41, Service Contract Labor Standards (May 2014), (41 U.S.C. chapter 67). (xi) (A) 52.222-50, Combating Trafficking in Persons (March 2, 2015) (22 U.S.C. chapter 78 and E.O. 13627). (B) Alternate I (March 2, 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627). (xii) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for Maintenance, Calibration, or Repair of Certain Equipment--Requirements (May 2014) (41 U.S.C. chapter 67.) (xiii) 52.222-53, Exemption from Application of the Service Contract Labor Standards to Contracts for Certain Services--Requirements (May 2014) (41 U.S.C. chapter 67) (xiv) 52.222-54, Employment Eligibility Verification (Aug 2013). (xv) 52.222-55, Minimum Wages Under Executive Order 13658 (Dec 2014) (E.O. 13658). (xvi) 52.225-26, Contractors Performing Private Security Functions Outside the United States (Jul 2013) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. 2302 Note). (xvii) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations. (May 2014) (42 U.S.C. 1792). Flow down required in accordance with paragraph (e) of FAR clause 52.226-6. (xviii) 52.247-64, Preference for Privately-Owned U.S. Flag Commercial Vessels (Feb 2006) (46 U.S.C. Appx 1241(b) and 10 U.S.C. 2631). Flow down required in accordance with paragraph (d) of FAR clause 52.247-64. (2) While not required, the contractor May include in its subcontracts for commercial items a minimal number of additional clauses necessary to satisfy its contractual obligations. (End of clause) 52.233-2 SERVICE OF PROTEST (SEP 2006) (a) Protests, as defined in section 33.101 of the Federal Acquisition Regulation, that are filed directly with an agency, and copies of any protests that are filed with the Government Accountability Office (GAO), shall be served on the Contracting Officer (addressed as follows) by obtaining written and dated acknowledgment of receipt from Christine L. Wilson, 5772 Iowa Avenue, Fort Leonard Wood, MO 65473. (b) The copy of any protest shall be received in the office designated above within one day of filing a protest with the GAO. (End of provision) 52.252-1 SOLICITATION PROVISIONS INCORPORATED BY REFERENCE (FEB 1998) This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at this/these address(es): HTTP://FARSITE.HILL.AF.MIL HTTP://WWW.ACQ.OSD.MIL/DPAP/DARS/INDEX.HTM HTTP://ACQUISITION.GOV/COMP/FAR/INDEX.HTML (End of provision) 52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998) This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es): HTTP://FARSITE.HILL.AF.MIL HTTP://WWW.ACQ.OSD.MIL/DPAP/DARS/INDEX.HTM HTTP://ACQUISITION.GOV/COMP/FAR/INDEX.HTML (End of clause) 252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (MAY 2013) (a) Definitions. As used in this clause-- Department of Defense Activity Address Code (DoDAAC) is a six position code that uniquely identifies a unit, activity, or organization. Document type means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF). Local processing office (LPO) is the office responsible for payment certification when payment certification is done external to the entitlement system. (b) ) Electronic invoicing. The WAWF system is the method to electronically process vendor payment requests and receiving reports, as authorized by DFARS 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports. (c) WAWF access. To access WAWF, the Contractor shall-- (1) Have a designated electronic business point of contact in the System for Award Management at https://www.acquisition.gov; and (2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this Web site. (d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the "Web Based Training" link on the WAWF home page at https://wawf.eb.mil/. (e) WAWF methods of document submission. Document submissions may be via Web entry, Electronic Data Interchange, or File Transfer Protocol. (f) WAWF payment instructions. The Contractor must use the following information when submitting payment requests and receiving reports in WAWF for this contract/order: (1) Document type. The Contractor shall use the following document types. COMBO (2) Inspection/acceptance location. The Contractor shall select the following inspection/acceptance location(s) in WAWF, as specified by the contracting officer. GOVERNMENT (3) Document routing. The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF when creating payment requests and receiving reports in the system. Routing Data Table* -------------------------------------------------------------------------------------------- Field Name in WAWF Data to be entered in WAWF -------------------------------------------------------------------------------------------- Pay Official DoDAAC HQ0490 Issue By DoDAAC W911S7 Admin DoDAAC W911S7 Inspect By DoDAAC W90NM2 Ship To Code W90NM2 -------------------------------------------------------------------------------------------- (4) ) Payment request and supporting documentation. The Contractor shall ensure a payment request includes appropriate contract line item and subline item descriptions of the work performed or supplies delivered, unit price/cost per unit, fee (if applicable), and all relevant back-up documentation, as defined in DFARS Appendix F, (e.g. timesheets) in support of each payment request. (5) WAWF email notifications. The Contractor shall enter the email address identified below in the "Send Additional Email Notifications" field of WAWF once a document is submitted in the system. Contracting Officer: Christine L. Wilson, christine.l.wilson2.civ@mail.mil Contract Specialist: David W. Foster: david.w.foster24.civ@mail.mil (g) WAWF point of contact. (1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity's WAWF point of contact. 5152.233-4000 5152.233-4000 AMC-LEVEL PROTEST PROGRAM (Sep 2011) (LOCAL CLAUSE) If you have complaints about this procurement, it is preferable that you first attempt to resolve those concerns with the responsible contracting officer. However, you can also protest to Headquarters, AMC. The HQ, AMC-Level Protest Program is intended to encourage interested parties to seek resolution of their concerns within AMC as an Alternative Dispute Resolution forum, rather than filing a protest with the Government Accountability Office or other external forum. Contract award or performance is suspended during the protest to the same extent, and within the same time periods, as if filed at the GAO. The AMC protest decision goal is to resolve protests within 20 working days from filing. To be timely, protests must be filed within the periods specified in FAR 33.10. If you want to file a protest under the AMC-Level Protest Program, the protest must request resolution under that program and be sent to the address below. All other agency-level protests should be sent to the contracting officer for resolution. Headquarters U.S. Army Material Command Office of Command Counsel-Deputy Command Counsel 4400 Martin Road RM: A6SE040.001 Redstone Arsenal, AL 35898-500 Facsimile number (256) 450-8840 or e-mail: amcprotest@conus.army.mil The AMC-Level Protest procedures are found at: http://www.amc.army.mil/amc/commandcounsel.html If internet access is not available, contact the contracting officer or HQ, AMC to obtain the AMC-Level Protest Procedures. Contracting Officer MICC- Fort Leonard Wood Attn: Christine L. Wilson 5772 Iowa Ave, Bldg 606 Fort Leonard Wood, MO 65473 Contract Specialist: David W. Foster: david.w.foster24.civ@mail.mil (2) For technical WAWF help, contact the WAWF helpdesk at 866-618-5988. (End of clause)

Replace Sewage Lift Station Pumps and Wiring

Department of Homeland Security, United States Coast Guard (USCG) | Published January 12, 2015  -  Deadline January 22, 2015
cpvs

1.1 WORK COVERED BY CONTRACT: Replace sewage lift station pumps and electrical components. 1.2 REFERENCES: NA 1.3 DESCRIPTION OF WORK TO BE COMPLETED: Replace sewage lift pumps and electrical components that control the system. Pumps will be replaced in kind. The electrical components inside the electrical panel and the remote float switches shall be replaced in kind as well. Project will be complete once pumps have been replaced with new pumps and works both remotely and locally by the float switches and at the local control box. Station Engineer Petty Officer Chief Thom Perry will verify proper operation and overall satisfaction before work is considered complete. 2.1 SITE VISIT: Those who desire access to the USCG Sta St Clair Shores facility for bidding or work are to contact MKC Thom Perry or DCC Anthony Graziano. Contractors are to arrange a start work date with USCG Sta St Clair Shores within two days of the project being awarded. 3.1 MILITARY REGULATION: The contractor, his employees and sub contractors shall become familiar with and obey all station regulations. 3.2 All personnel employed on the project shall keep within the limits of the work and avenues of ingress and egress. Personnel shall not enter any other areas outside the site of work unless required to do so in the performance of their duties and have obtained verbal permission from MKC Thom Perry, DCC Anthony Graziano or the Officer of the Day. 3.3 The contractor's equipment shall be conspicuously marked for identification. 3.4 There shall be no smoking in any Coast Guard building and only in designated areas. 4.1 WORK HOURS: The contractor shall perform all site work during the normal operation hours, 0700-1600 Mon-Fri except during federal holidays. 4.2 Any deviations from normal working hours will be discussed with MKC Thom Perry and agreed upon by all parties concerned. 5.1 LABORER WAGES: Quote must reflect hourly wages prescribed by the Department of Labor in the attached Wage Determination Document provided by the USCG Sector Detroit Contracting Officer CWO Terry Sorenson. 6.1 CLEAN UP OF WORK AREA: The contractor shall remove and properly dispose of all trash and debris pertaining to the contract work from the limits of government property, as well as adjacent affected areas. 6.2Disposal of HAZ MAT shall be in accordance with Federal, State and local regulations. 7.1 ACCEPTANCE OF WORK: Prior to the acceptance of work by the Coast Guard the contractor shall arrange through MKC Thom Perry and or DCC Graziano a review of work completed to ensure work satisfaction as well as proper clean up. Completed work shall meet the written scope of work. Coast Guard POC info: MKC Thom Perry (586) 778-3320 Thomas.A.Perry@uscg.mil DCC Anthony Graziano (313) 568-9474 Anthony.V.Graziano@uscg.mil

St. Stephen SC Fishlift Programmable Logic Controller

Department of the Army, U.S. Army Corps of Engineers | Published January 22, 2016
cpvs

DESCRIPTION:  The U.S. Army Corps of Engineers, Charleston District, has a requirement for the above subject Project. This announcement constitutes a Pre-Solicitation Notice. This is not a Request for Proposal (RFP). This is not a follow-on contract. This announcement is for information and planning purposes only and is not to be construed as a commitment by the Government, implied or otherwise, to issue a solicitation or award a contract. The Charleston District, U.S. Army Corps of Engineers (USACE) requires the services of a construction firm capable of managing a construction project for the Cooper River Rediversion Project located at 125 Rediversion Road, St. Stephen, SC. The Project consists of critical electrical repairs to the Fish Lift facility and incidental related work. The work includes, but is not limited to electrical repairs and component replacements as well as the replacement of the existing programmable logic controller (PLC), control console, transducers and transmitter boxes and all field wiring between the PLC and field wiring devices. Building(s) will be occupied during performance of work under this Contract. Before work is started, the Contractor shall arrange with the Contracting Officer a sequence of procedure, means of access, space for storage of materials and equipment, and use of approaches, corridors, and stairways. A detailed statement of work will be provided with the solicitation when it is posted. CONSTRUCTION MAGNITUDE:  The order of magnitude for this effort is estimated between $500,000.00 and $1,000,000.00.NAICS:  The North American Industrial Classification System Code (NAICS) for this effort is 238210 - Electrical Contractors and Other Wiring Installation Contractors.  Size limitation is $15M.TYPE OF SET-ASIDE:  This is a 100% Small Business set-aside.  The resulting award will be for one (1) Firm-Fixed-Price (FFP) contract.ANTICIPATED SOLICITATION RELEASE DATE:  The Government anticipates releasing the solicitation on or about 29 January 2016.  Actual dates and times will be identified in the solicitation.  Additional details can be found in the solicitation when it is posted to http://www.fbo.gov.  SOLICITATION WEBSITE:  The official solicitation, when posted, will be available free of charge by electronic posting only and may be found at Federal Business Opportunities website, http://www.fbo.gov.  Paper copies of the solicitation will not be issued.  Telephone and fax requests for this solicitation will not be honored.  Project files are Portable Document Format (PDF) files and can be viewed, navigated, or printed using Adobe Acrobat Reader.  To download the solicitation for this project, contractors are required to register at the Federal Business Opportunities website at http://www.fbo.gov.  Amendments, if/when issued, will be posted to the above referenced website for electronic downloading.  This will be the only method of distributing amendments prior to closing; therefore, it is the Offerors responsibility to check the website periodically for any amendments to the solicitation.REGISTRATIONS:  System for Award Management (SAM):  Offerors shall have and shall maintain an active registration in the SAM database at http://www.sam.gov to be eligible for a Government contract award.  If at the time of award an Offeror is not actively and successfully registered in the SAM database, the Government reserves the right to award to the next prospective Offeror.POINT-OF-CONTACT:  The point-of-contact for this procurement is MAJ Clarissa Cordon at clarissa.d.cordon@usace.army.mil or (843) 329-8015.  Secondary Point of Contact is Laurie Infinger at laurie.s.infinger@usace.army.mil. This announcement serves as the Advance Notice for this project.  Responses to this synopsis are not required.

48--2 Electric Actuators for the water control structure at Cross Lake MN

Department of the Army, U.S. Army Corps of Engineers | Published March 27, 2015  -  Deadline April 3, 2015
cpvs

SCOPE OF WORK Instructions to offerors: See page 1 block 8 for solicitation due date. Late offers will not be considered. SCOPE OF WORK: 1. SCOPE Provide Two (2) identical multi-turn actuators to be installed by others as replacements for existing gate hoist drives. Existing equipment is described on the drawings included with this solicitation. Actuators shall be designed and built in accordance with AWWA C542-09: Electric Motor Actuators for Valves and Slide Gates. 2. REQUIRED ACTUATOR PERFORMANCE POWER SUPPLY: Main is 480/277 volts AC, 3-phase, operators are powered by a 70-amp circuit breaker PF2 in Panelboard PDP1. Power to all of the gate operator enclosure heaters is supplied from a 20-amp breaker PGOH in Panelboard LRP. MINIMUM BREAK TORQUE (FT-LB) 6000 MAXIMUM TORQUE (FT-LB) 10000 TURNS TO OPEN 4.5 MINIMUM OUTPUT SPEED (RPM) 0.35 MINIMUM DUTY CYCLE AT BREAK TORQUE (SEC) 810 3. RECCOMENDED SITE VISIT INSPECTION OF EXISTING ACTUATORS Replacement actuators shall physically match existing actuators to the maximum extent to allow installation without modification to any other existing equipment. No modifications to existing hoist components will be allowed. Replacement actuator junction box, control panel, and hand wheel shall be in the same location and orientation and as the existing actuators. Replacement actuators shall have same mount bolt pattern and same output shaft dimensions and rotation direction as existing actuators. Replacement actuators shall be furnished complete with installation instructions and every part needed to complete the installations. The existing hoists are located at the Cross Lake Recreation Area, Crosslake, MN. The contractor is recommended to visit the site to inspect the existing actuators to obtain required measurements and layout information. Site visits to inspect the existing condition can be arranged and scheduled by contacting: U.S. ARMY CORPS OF ENGINEERS CROSS LAKE RECREATION AREA 35507 COUNTY ROAD 66, BOX 36 CROSSLAKE, MN 56442-0036 651-290-5793 4. ACTUATOR ENCLOSURES Furnish NEMA 4 cast iron or cast aluminum actuator enclosures for service in unprotected outdoors operating temperature range from -20 F to 150 F. All external fasteners shall be stainless steel. Provide space heaters inside enclosures wired same as existing heaters. Provide local control open/close/stop illuminated pushbutton station integral to enclosure. The control pushbutton station shall be configured so that quote mark open quote mark corresponds to gate raise and quote mark close quote mark corresponds to gate close as installed. Remote control operation and indication capability is not required. 5. ACTUATOR MOTORS AND GEARS Actuator shall not use a lost motion device to obtain required performance. Provide TENV 208 volt, single phase, capacitor start squirrel-cage induction motor, with NEMA MG1Class F insulation, and at least two Class B thermal contacts embedded within motor windings. All gears shall be enclosed. Shafts shall be mounted on antifriction bearings. Actuators shall be equipped with self-locking worm drives so to hold the gate load static at any manually selected shutoff position when the hoist is de-energized. Motor connection shall be by plug and socket and motor removal shall be possible without loss of lubricant. 6. ACTUATOR LIMIT SWITCHES Provide two independently adjustable position limit switches to serve as stop limiting devices for gate up and gate down positions. Motor shall include torque switches to de-energize the motor and prevent damage to the motor in the event of a stall condition. Limit switch contact rating rated 600 volts per ICS-125.6. 7. ACTUATOR HANDWHEEL AND CLUTCH Equip actuator with manual two-position clutch to select motor drive or hand wheel drive. Include external clutch handle with provision to padlock clutch handle in either position and to prevent unauthorized operation. Clutch shall prevent simultaneous engagement of motor and handwheel. The clutch system design shall provide that no damage results if hand operation is selected while the actuator is running. The clutch system design shall provide that no damage results if the actuator motor is started when hand operation is selected. The handwheel shall include an embossed / raised arrow to indicate gate open direction. 8. SUBMITTAL REQUIRED WITH BID All submittal information shall be in pdf format. Submit with the bid the make and model number of the actuator complete with dimensioned outline drawings and performance data. Submittal shall be sufficiently detailed to verify compliance with the specified actuator performance and layout criteria. 9. SUBMITTALS AFTER CONTRACT AWARD All submittal information shall be in pdf format. MODEL AND DESIGN DATA SUBMITTAL. For each actuator furnish complete job sheet including model number, purchase order, serial number, options, and point of contact for service and parts. Provide information required by Par. 4.2 of AWWA C542. For each actuator provide Certification and copy of both Proof-of-Design Test and Performance Test as defined by AWWA C542. OPERATION AND MAINTENANCE INFORMATION SUBMITTAL. Provide manufacturers standard package of instructions and information exploded view with parts list plus specified installation instructions. Include disassembly and troubleshooting instructions with exploded view of actuator components and itemized list of replacement parts. Include wiring diagrams, and limit switch and torque switch setting instructions. Include unit weight, hoisting instructions, and installation instructions. SHOP DRAWING SUBMITTAL. Provide manufacturers standard dimensioned outline drawing. In addition, provide detail drawings to completely describe the mount interface between the new actuator and the existing hoist gear reducer. Include fully dimensioned drawings of actuator mount including bolt pattern, output shaft, and coupling. WIRING DIAGRAM SUBMITTAL. Include manufacturer's standard wiring diagrams. Include job-specific wiring instructions to identify individual existing actuator conductors and locations, modifications to these conductors, and new locations in the new actuators. Wiring instructions shall include images of both existing actuator junction terminals and new actuator junction terminals with arrows, callouts, conductor identifications, and other information to aid field installation. INSTALLATION PARTS SUBMITTAL. For each actuator, provide all electric conduit, fittings, enclosures, and preassembled wire harnesses as required to complete the electrical installation. For each actuator, provide fully machined output drive coupling, keys, mount bolts, gaskets, and all required fasteners that are required to complete installation. 10. EXISTING EQUIPMENT Actuator Data: EIM Model No: 3FNK-3 Outline Dwg: 3-001/16G 84195-2H Assembly Dwg: 83854D-1 83854D-2 Instruction: Tech Manual Enclosure: Watertight NEMA 4/IP65 RPM Out: 025 Torque Spring: 83464-5 White Motor Gears: 33941/33927 Handwheel Gears: 16/32 33941/34545 Drive Sleeve/Worm: 35600-2R 68:2R Lubrication: #221 Moly 800 E.P. Special Cover: Lockable C/S Cover Nameplate: 36685 NEMA 4X, IP 66 Rated torque: 255 ft-lb Pullout torque: 330 ft-lb Peak (stall) torque: 600 ft-lb Design stall thrust: (600) (1.15) / (.0275) = 25,090 lb

St. Anthony Bunkhouse Site Work Project on the Caribou-Targhee National Forest

Department of Agriculture, Forest Service | Published June 29, 2016  -  Deadline August 5, 2016
cpvs

Quotes are being solicited by the USDA, Forest Service for the St. Anthony Bunkhouse Site Work project located in St. Anthony, Idaho on the Caribou-Targhee National Forest in Idaho. The project consists of removal of existing lift station and wet well and the installation of a new lift station, water, sewer and electrical lines to two bunkhouses. This requirement is being solicited as a Firm-Fixed Price Request for Quotes. The approximate start work date will be September 1, 2016. Quotes are due at 1:00 p.m. MST, August 5, 2016. The estimated price range is between $25,000 and $100,000. The solicitation will be available on approximately July 15, 2016 and may be downloaded from this site at that time. All future information about this acquisition, including amendments, will be distributed solely through this site. Interested parties are responsible for monitoring this site to ensure that they have the most up-to-date information about this acquisition. Vendors are required to be registered in the System for Award Management (SAM). All responsible sources may submit a response to this announcement which will be considered by this agency.

Y--Construct Bldg. 108 IT Center St Cloud VA 656-16-1-2393-0003 Presolicitation notice, solicitation to follow after 3/16/16.

Department of Veterans Affairs, Minneapolis VAMC | Published March 2, 2016  -  Deadline March 16, 2016
cpvs

DESCRIPTION OF THE PROGRAM: This pre-solicitation notice is for commercial construction services to construct a new IT data center on the St. Cloud VA Medical Center Campus. The magnitude of construction for this project is bbetween $2,000,000 and $5,000,000. This solicitation will utilize Veteran Owned Small Business (VOSB) in accordance with Statute FAR 6.302-5 and in support of Department of Veterans Affairs' socio?economic goals. The new 4,460 square feet IT Center will provide 50% additional data capacity and modernize the IT infrastructure. Work includes but is not limited to general construction, metals, wood, plastics and composites, thermal and moisture protection, openings, finishes, furnishings, fire suppression, plumbing, HVAC and mechanical, electrical, multiple communications systems, electronic safety and security, earthwork and exterior improvements, utility systems and electrical power generation. The planned work also includes a very significant amount of low?voltage cabling, including connection of approximately 17,000 existing copper wire pairs into the new data center. Because of this requirement, the selected contractor must have strong IT and low voltage knowledge. Applicable conditions: This is an approved FY16 NRM project. Award will be made to a Veteran Owned Small Business 1. This contract requires extensive access to VA Information Technology and data areas. Due to the sensitive information contained in these secure areas, the Contractor or sub-contractors will be required to have an escort from the VA when entering, and while executing work in these areas. These areas can be defined as any areas that contain secure VA communications and data equipment that requires a clearance or specific VA credentials to enter. These areas include but are not limited to individual building data closets, and building 108, the current campus data center. a. The contractor must coordinate with his sub-contractors to determine in advance when access to these defined areas will be needed. b. Request for access and escort shall be submitted in writing to the COTR a minimum of 10 business days prior to the day access is requested. Request shall include: building and room the work is being executed in, summary of work to be executed and the expected duration of the work. The COTR will coordinate access with SCVAMC OI&T staff. The VA will make all reasonable efforts to provide access/ escort at the requested date and time. If the specific date and time requested is not available the COTR will provide the contractor the closest available dates and times escort is available. c. The contractor should have subsequent work scheduled in the event the specific dates and times requested are not available. In the event the first available date for access/ escort exceeds the requested access date by 72 hours (not including weekends and holidays) the Contracting Officer shall be notified in order to make a determination as to whether the postponement of access constitutes a legitimate delay, and if a modification to the contract is required.

Passenger Elevators Replacement

General Services Administration, Public Buildings Service (PBS) | Published February 24, 2016  -  Deadline April 11, 2016
cpvs

The General Services Administration (GSA), Great Lakes Region, Acquisition Management Division (AMD) is issuing this synopsis for the replacement of six (6) Passenger Elevators, located at the Warren E. Burger Federal Building and US Courthouse, 316 N. Robert Street, St. Paul, Minnesota. This procurement is an unrestricted (Full and Open) procurement. The estimated cost is between $1,000,000 and $5,000,000. The NAICS code is 238290, Other Building Equipment Contractors. The Small Business Size Standard is $15 Million. For general reference, the scope of this project requires the contractor to furnish all labor, equipment, tools, materials, and supervision necessary for the removal and replacement of the existing passenger elevators as indicated in the specification and drawings. The contract will consist of one line item. Work includes but is not limited to the demolition and replacement of elevators, to be completed in two phases for three (3) elevators each. Work also includes installation of sump pumps at the related elevator pits. Work will include all general, mechanical and electrical work specified in the Specifications and Drawings. The Government intends to award a contract in the third quarter (April 1, 2016 - June 30, 2016) FY16. The Contractor will need to reach substantial completion within 240 calendar days from the issuance of the Notice to Proceed (NTP) with on-site work. Contract completion will be expected within 60 calendar days after the substantial completion date. It is the Government's intent to award a contract to the responsible offeror whose proposal conforms to the solicitation and provides the best value to the Government based on the following evaluation factors: Price and Past Performance. The Solicitation will be released on or about March 10, 2016, with a proposal due date on or about April 11, 2016. A pre-proposal site visit will be scheduled within two weeks of the issuance of the solicitation. The entire scope of work, inclusive of drawings and technical documents will be available through Federal Business Opportunities. Interested parties are responsible for printing the Solicitation and all related documents. It is also the interested parties' responsibility to monitor this site for release of the Solicitation, amendments and any other related information. Funds are current unavailable, however, funding is anticipated third quarter of FY16. One or more of the items under this acquisition is subject to Free Trade Agreements. All responsible sources may submit a proposal which shall be considered by the agency. All contractors must be active in SAM www.sam.gov, to be considered for award. For any questions related to this synopsis, please contact the Contracting Officer, Ron Sieben, at 612-725-3018 or ronald.sieben@gsa.gov.