Public tenders for electrical in Redstone-arsenal United States

Find all Electrical tenders in the world.
Finding business opportunities has never been easier.

Results for electrical. Make a new search!
ElectricalUnited Statesredstone-arsenal

Z--REVITALIZE ELECTRICAL SYSTEMS FOR THE CENTRAL CHILLER FACILITY AT BUILDING4473

National Aeronautics and Space Administration, Marshall Space Flight Center | Published September 25, 2015
cpvs

The work to be performed under this project consists of providing the labor, equipment, and materials necessary to perform the upgrade, replacement, addition or removal of most of the electrical distribution equipment for Building 4473. Work will include, but is not limited to: The replacement of primary and secondary cabling, transformers, and utility switches as shown on construction drawings; Installation of primary cabling to the existing switchgear locations inside the facility; Installation of secondary cabling to the existing and new switchgear inside the facility; Installation of a new section of switchboard to the existing switchboard to facilitate easy switchover from the old system to the new system during electrical outages; Removal or replacement of multiple 480, 4160, and 12,470 volt main service entrances; Installation of a new dual transformer, 46KV to 12,470 volt substation to handle the six primary service to the existing facility; Installation of primary metering to the new substation; Replacement of exterior, oil-type transformers. The work performed under this project will primarily be electrical work with work in the Mechanical, Structural and Civil as needed to support the installation of the new electrical equipment.

Z--REVITALIZE ELECTRICAL SYSTEMS AT BUILDING 4711

National Aeronautics and Space Administration, Marshall Space Flight Center | Published October 29, 2015
cpvs

NASA/MSFC plans to issue an Invitation for Bids (IFB) for the requirement Revitalize Electrical Systems at Building 4711. The work to be performed under this project consists of providing the labor, equipment, and materials to perform the renovation of the office, labs, and high bay area electrical systems for Building 4711 at Marshall Space Flight Center (MSFC) near Huntsville, Alabama. This effort includes, but is not limited to, the following: Replacement of service entrance switchgear. Replacement of the bus duct system throughout the building. Replacement of panels. Replacement of circuit breakers, disconnects, and transformers. Upgrades to the existing fire alarm system. Installation of new lightning protection system. Replacement of existing light fixtures in office areas with LED fixtures. Replacement of existing light fixtures in high bay with LED fixtures. Replacement of existing wall-mounted light fixtures with LED fixtures. The work performed under this project will primarily be electrical work with work in the mechanical, structural, and civil as needed to support the installation of the new electrical equipment. The magnitude of the procurement is between $1 million to $5 million, and the effort shall be completed within 365 calendar days after the Notice to Proceed (NTP). Award of this project is contingent upon the availability of funds. This procurement is a HUBZone set-aside. Potential bidders must a HUBZone certified small business concern, have a certificate issued by the Small Business Administration (SBA), and be on the SBAs List of Qualified HUBZone Small Business Concerns at http://dsbs.sba.gov/dsbs/sea rch/dsp_searchhubzone.cfm as noted at Federal Acquisition Regulation (FAR) 19.1303, Status as a HUBZone Small Business Concern. The NAICS Code and small business size standard for this procurement are 236220 and $36.5M in average annual receipts, respectively. The anticipated release date of the IFB is on or about November 12, 2015, with an anticipated closing date on or about December 14, 2015. The firm date for receipt of bids will be stated in the IFB. The specification/drawing package supporting this requirement will be posted with the solicitation. All responsible sources may submit a bid which shall be considered by the agency. Safety records of the prime contractor and subcontractor will be a consideration at award time, and the prime contractor must have an EXPERIENCE MODIFICATION RATING (EMR) of 1.0 or less and proof included within the bid package. The prime subcontractors EMR rating shall be no more than 1.1. NASA Clause 1852.215-84, Ombudsman, is applicable. The Center Ombudsman for this acquisition can be found at http://prod.nais.nasa.gov/pub/p ub_library/Omb.html . The solicitation and any documents related to this procurement will be available over the Internet. These documents will reside on a World-Wide Web (WWW) server, which may be accessed using a WWW browser application. The Internet site, or URL, for the NASA Business Opportunities page is http://procurement.na sa.gov/cgi-bin/EPS/bizops.cgi?gr=D&pin= . Prospective bidders may notify this office by e-mail of their intent to submit a bid. It is the bidders responsibility to monitor the Internet site for the release of the solicitation and amendments (if any). Potential bidders will be responsible for downloading their own copy of the solicitation (to include the specification/drawing package) and amendments (if any). The clauses at 52.236-2, Differing Site Conditions, and 52.236-3, Site Investigations and Conditions Affecting the Work, will be included in any contract awarded as a result of the solicitation. Accordingly, bidders will be required to inspect the site where the work will be performed. The date(s) of the organized site visit(s) will be stated in the IFB. All contractual and technical questions must be submitted in writing. Telephone questions will not be accepted.

10--CONTROL BOX, ELECTRICAL

Department of the Army, Defense Logistics Agency Detachment | Published November 14, 2013  -  Deadline December 16, 2013
cpvs

**No telephone requests will be accepted. Direct your requests and communication to: ATTN: Megan Mann, Contract Specialist via email at megan.mann@dla.mil and/or Janeze Allison, Contracting Officer , via email janeze.allison@dla.mil or facsimile 256-955-8601. For request for solicitation, provide your name, the company name and Cage Code and a telephone/facsimile number.*** PRON: AX4F0020AX. The Government proposes to acquire on a 5 year Indefinite Delivery Indefinite Quantity contract (IDIQ) for a minimum quantity of 25 each/maximum quantity of 125 each, of a Control Box, Electrical, NSN:1055-01-576-8810, Part Number: A102859-101 applicable to the BE-UH60 Blackhawk Helicopter. Production Lead Time with First Article Testing is 25 each, 203 Days After Contract Award (DACA) with deliveries to New Cumberland, PA, 17070-5002. This item is restricted to Lockheed Martin (Cage Code 622B7). The rights to use the data needed to purchase this part from additional source(s) are not owned by the Government and cannot be purchased, developed, or otherwise obtained. Firms that recognize and can produce the required item described above are encouraged to identify themselves. Firms are encouraged to seek source approval in order to compete for future solicitations by accessing the website: http://amcomdmz.redstone.army.mil/casl_cmo/casldba.casl_cmo_samsar and looking under Standardized Aviation and Missile Source Approval Request SAMSAR. All responsible sources may submit an offer, which shall be considered by the Agency. The closing date annotated is an estimated date and may be adjusted dependent upon the date of release for solicitation; however, the solicitation will not close prior to the date stated above. Foreign Firms are reminded that all requests for solicitation must be processed through their respective embassies. THIS ACQUISITION CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, USC., SEC 2751 ET SEQ) OR THE EXECUTIVE ORDER 12470.VIOLATION OF THESE EXPORT LAWS ARE SUBJECT TO SEVERE CRIMINAL PENALTIES.

Subject: Electrical Sequencing Control Unit

Department of the Army, Army Contracting Command | Published March 8, 2016  -  Deadline March 23, 2016
cpvs

Description: The contractor shall furnish all labor, facilities, parts, materials, equipment, tools and data (other than Government Furnished Property), necessary to accomplish the overhaul of the following assets: Nomenclature: Overhaul of Electrical Sequencing Control UnitInput NSN: 6110-01-328-5258Input P/N: 2118806-12118806-22118806-2-12118806-2-2Output NSN: 6110-01-328-5258Output P/N: 2118806-2-2Estimated Quantity Range: 82 Minimum, 468 Maximum (78 FMS) The proposed contractual action will be a Firm Fixed Price Maintenance and Overhaul type contract, with the quantities listed above. These items are non-commercial; FAR Part 12 will not be utilized. Required delivery shall be FOB Origin. This procurement is restricted to Honeywell International, Inc. (CAGE Code 64547), 11100 North Oracle Road, Tucson, AZ 85737-9588. Technical data is not available to support a full and open competitive solicitation. The overhaul shall be accomplished in accordance with the Original Equipment Manufacturer overhaul specifications and drawings. These items have not been identified as a Critical Safety Items (CSI). Firms that recognize and can produce the required item described above are encouraged to identify themselves. Firms are encouraged to seek source approval in order to compete for future solicitations by accessing the website: http://amcomdmz.redstone.army.mil/casl_cmo/cmo_home and looking under Standard Aviation and Missile Source Approval Request (SAMSAR). All responsible sources may submit an offer which shall be considered by the Agency. No telephone requests for the solicitation will be accepted. Requests for the solicitation shall be by mail. You may mail your request to ACC-RSA, Building 5303, 2nd Floor ATTN: CCAM-ALM (Audrey Peterson), Redstone Arsenal, AL 35898-5000. Proposals can be hand-carried, mailed via the US Postal Service, or delivered by a commercial delivery service. No FAX or email responses shall be accepted for the initial proposal. This requirement is currently unfunded. Award will be withheld pending receipt of sufficient funds. The closing date annotated is an estimate date and may be adjusted dependent upon the date of release of the solicitation; however, the solicitation will not close prior to the closing date stated above.

Electrical Test Process & Augmented Machine Learning Algorithm

Other Defense Agencies, Missile Defense Agency | Published July 6, 2015
cpvs

Missile Defense Agency - June 26, 2015 Contract Announcement Howard University, Washington, DC, is being awarded a contract with a maximum value of $261,324. Under this new competitive, cost reimbursement contract, the contractor will develop an electrical test process and augmented machine learning algorithm, which would reliably discover data correlations across various data points of the integrated circuit. Through statistical analysis, the data fusion engine will identify failures and potentially counterfeit parts. The work will be performed at Howard University, Washington, DC, in offices and laboratory facilities within the Communications and Signal Processing Laboratory, University Nanoscale Science and Engineering Facility, and Polyvea Incorporated with an estimated completion date of June 25, 2018. This contract was competitively procured via publication on the Federal Business Opportunities website under the MDA's Broad Agency Announcement for Advanced Technology Innovation (ATI); HQ0147-13-ATI-BAA. Fiscal year 2015 Research, Development, Test and Evaluation funds in the amount of $175,000 are being obligated on this award. In accordance with FAR 35.006 (c), the use of a cost reimbursement contract for this research and development effort is appropriate. This is not a Foreign Military Sales acquisition. The Missile Defense Agency, Redstone Arsenal, Alabama is the contracting activity. (HQ0147-15-C-6005) Contracting Office Point of Contact: Willis Brice (256) 450-4790 Approved for Public Release 15-MDA-8297 (29 June 15)

CONNECTOR�ASSEMBLY,�ELECTRICAL

Defense Logistics Agency, DLA Acquisition Locations | Published August 16, 2016  -  Deadline August 31, 2016
cpvs

  NOMENCLATURE: W22 PLUG ASSY PART NUMBER: A100625-101 NSN: 5935-01-574-8222

59--Connectors, Electrical

Department of the Army, Army Contracting Command | Published April 4, 2016
cpvs

No Description Provided

61--Sources Sought for the Electrical, Sequencing Control Unit

Department of the Army, Army Contracting Command | Published August 25, 2015  -  Deadline September 14, 2015
cpvs

DESCRIPTION: This is a sources sought announcement. This announcement is in support of market research to determine the feasibility of a competitive acquisition and to identify potential sources that can provide the overhaul of the following item: NOMENCLATURE: Electrical, Sequencing Control Unit INPUT NSN: 6110-01-328-5258 INPUT P/N: 2118806-1 2118806-2 2118806-2-1 2118806-2-2 OUTPUT NSN: 6110-01-328-5258 OUTPUT P/N: 2118806-2-2 ESTIMATED QUANTITY RANGE: Minimum 82 each; Maximum 468 each (Maximum includes a Foreign Military Sales (FMS) Quantity of 78 each) The applicable North American Industry Classification System (NAICS) code is 335312 and the size standard is 1000 employees. Interested parties who have the capability to perform the above effort should respond to this notice and identify your business size and socio-economic status as applicable. All submissions must include full company names, Point of Contacts (POCs) to include, name, position, office and mobile telephone numbers and email address. No DMWR has been identified for this effort. This is not a Critical Safety Item (CSI). Contractors are encouraged to seek Source Approval Requests (SAR) in order to become an approve source by submitting documentation in accordance with the Competition Advocate's Shopping List procedures. These procedures are outlined at the following website: http://amcomdmz.redstone.army.mil/casl_cmo/casl_cmo_home. This announcement is for information and planning purposes only and should not be construed as a commitment by the Government for any purpose. This announcement does not constitute a RFP. A synopsis will be issued at a later date for this requirement. Requests for a solicitation will not receive a response. No reimbursement will be made for any costs associated with providing information in response to this announcement and any follow-up information requested. No basis for claim against the Government shall arise as a result of a response to this announcement or Government use of any information provided. This announcement does not restrict the Government to an ultimate acquisition strategy. The Government reserves the right to consider acquisition strategies as deemed appropriate. Submittal of information is requested via electronic mail only to Audrey Peterson, Contract Specialist, audrey.m.peterson6.civ@mail.mil, no later than September 14, 2015.

61--Electrical Control Equipment

Department of the Army, Army Contracting Command | Published September 1, 2016
cpvs

No Description Provided

61--Converters, Electrical, Nonrotating

Department of the Army, Army Contracting Command | Published September 9, 2016
cpvs

No Description Provided

59--Electrical Hardware and Supplies

Department of the Army, Army Contracting Command | Published April 25, 2016
cpvs

No Description Provided

66--Overhaul of Indicator, Electrical Tachometer (OH-58 A/C)

Department of the Army, Army Contracting Command | Published April 8, 2015  -  Deadline May 8, 2015
cpvs

The contractor shall furnish all labor, facilities, parts, materials, equipment, tools and data (other than Government Furnished Property), necessary to accomplish the overhaul of the following assets: NOMENCLATURE: Indicator, Electrical Tachometer (OH-58 A/C) INPUT NSN / PART NUMBER'S: 6680-01-081-9181 / 206-075-713-101, SEDL-C329C OUTPUT NSN / PART NUMBER: 6680-01-081-9181 / SEDL-C329C ESTIMATED QUANTITY RANGE: 30 Minimum - 180 Maximum (30 FMS) The proposed contractual action will be a Five (5) year, firm fixed price Indefinite Delivery Indefinite Quantity (IDIQ) Maintenance and Overhaul type contract, with minimum / maximum quantities listed above. The maximum quantity of 180 each includes a quantity of 30 each for Foreign Military Sales (FMS). These items are commercial; FAR Part 12 will be utilized. Required delivery shall be FOB Origin. This NSN is not a critical safety item. This procurement will be solicited as a 100% Small Business Set-aside. Depot Maintenance Work Requirement DMWR-55-6680-306 and all associated Maintenance Engineering Orders are adequate and available to support the overhaul of the subject item. A Product Verification Audit (PVA) IS required. Offers are not solicited from other than small business concerns. By U.S. law, participation in small business set-asides are restricted to U.S. small businesses, therefore foreign request for this solicitation will not be honored. No telephone requests for the solicitation will be accepted. Requests for the solicitation shall be by FAX, mail, or email. You may mail your request to Joseph R. Thomas, CCAM-ALM, Bldg 5303, 2nd Floor, Redstone Arsenal, AL 35898-5000. Email requests should be sent to joseph.r.thomas90.civ@mail.mil. Proposals can be hand-carried, mailed via the US Postal Service, or delivered by a commercial delivery service. No FAX or email responses shall be accepted for the initial proposal. This requirement is currently unfunded. Award will be withheld pending receipt of sufficient funds. The closing date annotated is an estimate date and may be adjusted dependent upon the date of release of the solicitation; however, the solicitation will not close prior to the closing date stated above.

ENGINE ELECTRICAL SYSTEM COMPONENTS, NONAIRCRAFT

Department of the Army, Army Contracting Command | Published April 4, 2016  -  Deadline May 3, 2016
cpvs

No Description Provided

59--MISCELLANEOUS ELECTRICAL AND ELECTRONIC COMPONENTS

Department of the Army, Army Contracting Command | Published May 12, 2016
cpvs

No Description Provided

61--GENERATORS AND GENERATOR SETS, ELECTRICAL

Department of the Army, Army Contracting Command | Published April 7, 2016
cpvs

No Description Provided

Cable Assy, Special Purpose, Electrical W577

Defense Logistics Agency, DLA Acquisition Locations | Published August 25, 2016  -  Deadline September 9, 2016
cpvs

Small Business Set Aside for procurment of 5 Cable Assemblies, NSN 6150-01-465-9894, part # 11477804.  Federal Prison Industries is included.

Z--REVITALIZE ELECTRICAL SYSTEMS AT BUILDING 4711

National Aeronautics and Space Administration, Marshall Space Flight Center | Published February 1, 2016
cpvs

Link To Document

H--INSPECTION- ELECTRICAL AND ELECTRONIC EQUIPMENT COMPONENTS

Department of the Army, Army Contracting Command | Published March 3, 2016
cpvs

No Description Provided

29--ENGINE ELECTRICAL SYSTEM COMPONENTS, NONAIRCRAFT

Department of the Army, Army Contracting Command | Published January 30, 2015
cpvs

No Description Provided

66--ELECTRICAL AND ELECTRONIC PROPERTIES MEASURING AND TESTING INSTRUMENTS

Department of the Army, Army Contracting Command | Published September 13, 2016
cpvs

No Description Provided