Call +44 800 9755 164

Public tenders for electrical in Canada

Find all Electrical tenders in the world.
Finding business opportunities has never been easier.

Results for electrical. Make a new search!

Electrical repairs & upgrade

Fisheries and Oceans Canada | Published January 26, 2017  -  Deadline September 2, 2017
cpvs

Statement of Work

This project is to repair or upgrade all the electrical related items identified in the last building condition inspection as follows:

  1. Electrical Room main breaker to be replaced, and the existing breaker to be serviced & used as a spare
  2. Electrical Room unit heater replacement
  3. Operational indicators for well house pumps to be tested and repaired as necessary.
  4. Thermographic analysis of all existing switchboard, transformer, etc., and clean, check all electrical equipment in Electrical Room 120 to factory recommended specifications
  5. Extend transformer ground for Right Wing Fish Pond Structure to main service ground
  6. Repairing fish feeder electrical system
  7. Installation of six (6) pull stations
  8. Electrical work to make electric hoists in Sorting Building to be able to operate with a portable emergency generator.
  9. Electrical work in the Chemical Storage room for the existing lamps, air proving switches, exhaust fans etc.
  10. Replacement of Washroom hand dryer in the Administration Building.
  11. Make Locker/Storage room exhaust fan to run 24 hours/day
  12. Replacement of existing lighting in Mechanical room basement with waterproof lighting
  13. Install new receptacles with ground fault breakers for Garage Building.
  14. Electrical work to make Administration Building office area to be able to operate with a portable emergency generator

    Additional requirements of the project

  1. The construction schedule shall not interrupt the Science Program on site.
  2. The contractor will demonstrate to the project engineer during the final inspection that the contract documents are followed.
  3. The contractor is to provide price to supply and install all labour, materials, permits, etc… for this project.
  4. The contractor will include the information about the warranty (period and items to be covered)
  5. The contractor will provide the as-built drawings in one-week following the project substantial completion inspection.

    Work Schedule

  1. Project completion by March 31, 2017.
  2. Notifying the project engineer once the work is completed, the project engineer will co-ordinate final inspection
  3. Provide at least 48 hours advanced notice to the project engineer before coming to the site for the first time to start the work

    LOCATION OF WORK, WORK SITE AND DELIVERY POINT:

    114 Fish Hatchery Lane, Kingsclear, NB E3E 2C6

    FAMILIARIZATION WITH SITE:

    Site visit is mandatory before tender closing. The site visit will occur twice over a one (1) day period. Contractors wishing to visit the site must contact by email the Senior Contracting Officer listed below.

Contractors, bidders, or those they invite to site are to review specification Section 01 35 28 – “Health and Safety Requirements” before visiting site. Take all appropriate safety measures for any visit to site, either before or after acceptance of bid.

CABLE ASSEMBLY, POWER,ELECTRICAL

Department of National Defence | Published January 27, 2017  -  Deadline March 28, 2017
cpvs

The Department of National Defence has a requirement for the items detailed below. The delivery is requested at CFB Halifax and CFB Esquimalt by 12 May 2016.

Item 1, GSIN: 6150, NSN: 99-501-2252, Cable Assembly, Power, Electrical

Part No.: CGBUW95520606 NCAGE: U3212

Quantity: 8, Unit of Issue: EA, to be delivered to CFB Esquimalt.

Item 2, GSIN: 6150, NSN: 99-501-2252, Cable Assembly, Power, Electrical

Part No.: CGBUW95520606 NCAGE: U3212

Quantity: 2, Unit of Issue: EA, to be delivered to CFB Halifax.

Bidders proposing an Equivalent or a Substitute Product must indicate the brand name and model and/or Part Number and the NCAGE they are offering.

This procurement is subject to the Controlled Goods Program. The Defence production Act defines Canadian Controlled Goods as certain goods listed in Canada’s Export Control List, a regulation made pursuant to the Export and Import Permits Act (EIPA).

The Crown retains the rights to negotiate with suppliers on any procurement.

Documents may be submitted in either official language of Canada.

Mechanical and Electrical Upgrade – Halifax Citadel

Parks Canada | Published February 15, 2017  -  Deadline March 29, 2017
cpvs

5P300-l6-5479 - Mechanical and Electrical Upgrade – Halifax Citadel

Description of Work: Parks Canada Agency (PCA) is inviting engineering firms to submit a proposal for the provision of mechanical and electrical engineering and prime consultant services. This procurement will follow a one phase submission process. The selected consultants shall provide a range of engineering services including, but not limited, investigation and recommendation reports, professional advice on mechanical and electrical engineering methodology, as well as design and construction services for projects at the Halifax Citadel. Project will include the renovation, rehabilitation and new construction of the following type of real property assets and installations:

Mechanical and electrical Engineering and prime consultant services are required, Consulting services are required to assist PCA to provide a range of planning, design and construction supervision services.

Closing Date and Time: March 29, 2017 at 2:00 PM EST

Optional Site Visit: There will be a site visit on Thursday March 2, 2016 at 1:30 PM (AST). Interested bidders are to meet at Halifax Citadel, National Historic Site, 5425 Sackville Street, Halifax, NS, Canada B3J 3Y3. The meeting will be held in the Cavalier Building, third floor boardroom. (The Cavalier Building is located inside the Halifax Citadel, it is the building in the centre of the parade).

Bidders that consider themselves qualified to provide this Work and intend to submit bids on this project should obtain documents from the Government Electronic Tendering Service through the Government of Canada tendering service at www.buyandsell.gc.ca/tenders . Addenda, when issued, will be available from the Government of Canada tendering service. Bidders that elect to base their bids on documents obtained from other sources do so at their own risk. Late submissions will not be considered.
Standard Terms and Conditions for this procurement are incorporated by reference into, and form part of the Tender and Contract Documents.

Delivery Date: The Work must be completed on or before December 20, 2018.

Inquiries:

All inquiries of a technical and contractual nature are to be submitted to the Contracting Authority: Michel Marleau, telephone: (613) 938-5822, facsimile (866) 246-6893, e-mail: michel.marleau@pc.gc.ca. Inquiries are to be made in writing and should be received no less than ten (10) calendar days prior to the closing date to allow sufficient time to respond.

This PCA office provides procurement services to the public in either official language of Canada.
The Crown retains the right to negotiate with suppliers on any procurement.
Documents may be submitted in either official language of Canada.

Bid Receiving:

Sealed tenders will be received in English or French at the following address:

Parks Canada Agency – Central Registry
111 Water Street East
Cornwall, Ontario K6H 6S3

Direct Deposit

In April 2012, the Government of Canada announced that it will be replacing cheques with electronic payments by April 2016. Contract payment(s) currently made by cheque will be replaced by Direct Deposit. Businesses are encouraged to proactively enrol with Parks Canada. Please contact [Name] at [email address] in order to obtain a Direct Deposit enrollment form.

Additional information on this Government of Canada initiative is available at:

http://www.directdeposit.gc.ca

Electrical Services, Cold Lake, Alberta

Department of National Defence | Published December 7, 2016  -  Deadline June 1, 2017
cpvs

Trade Agreement: Agreement on Internal Trade (AIT) Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   Regional Individual Standing Offer for the provision of skilled licensed labour, tools, equipment, transportation, supervision and material necessary to perform electrical services on an as required basis for Department of National Defence, 4 Wing Cold Lake, Cold Lake, Alberta.  It is anticipated that three (3) standing offers will be issued to the lowest compliant offerors.  The standing offer will be issued for a term of two (2) years plus two (2) additional one - year option period from the date of Standing Offer issuance.  THIS DOCUMENT CONTAINS A SECURITY REQUIREMENT For further instructions, please see Part 6, Article 1, Security Requirement and Part 7, Article 2, Security Requirement.  Email  mony.lee@pwgsc-tpsgc.gc.ca  This PWGSCOffice provides procurement services to the Public in English.  IMPORTANT NOTICE TO BIDDERS  Bidders are responsible for obtaining copies of bid forms, special instructions and amendments issued prior to bid closing, and are to ensure they are addressed in the submitted bid.  Notifications about amendments to an opportunity: Buyandsell.gc.ca/tenders provides a Web feed to keep you informed about amendments to an opportunity of interest.  Firms intending to submit bids on this project should obtain bid documents through the GETS service provider on the Government of Canada Web site at http://buyandsell.gc.ca/procurement-data/tenders. Firms that obtain bid documents from a source other than the official site run the risk of not receiving a complete package.    Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

Notice of Proposed Procurement – Supply and delivery of electrical supplies – Canal-de-Chambly National Historic Site, Quebec

Parks Canada | Published December 19, 2016  -  Deadline April 1, 2017
cpvs

This solicitation and the resulting Contract are issued against the Supply Arrangement (SA), PWGSC File No. E60HN-12ELEC/…/HN and all terms and conditions of the SA apply. Solicitation documents have been sent to holders of a SA for the Quebec region.

Description of Work: Supply and delivery of materials required for the electrical upgrading of bridges 3, 7 and 10 of the Chambly canal.

Closing Date and Time: Wednesday, January 4, 2018 at 2:00 p.m. (EST).

Late submissions will not be considered.
Standard Terms and Conditions for this procurement are incorporated by reference into, and form part of the Tender and Contract Documents.

Delivery Date: All of the materials must be delivered to the site within fifteen (15) business days after contract award.

Inquiries:

All inquiries of a technical and contractual nature are to be submitted to the Contracting Authority: Céline Morin, e-mail: celine.morin@pc.gc.ca. Inquiries are to be made in writing and should be received no less than three (3) business days prior to the closing date to allow sufficient time to respond.

This PCA office provides procurement services to the public in either official language of Canada.
The Crown retains the right to negotiate with suppliers on any procurement.
Documents may be submitted in either official language of Canada.

Bid Receiving:

Sealed tenders will be received in English or French by fax at 1-877-558-2349 or at the following address:

Parks Canada Agency

National Contracting Service

111 Water Street East

Cornwall, ON K6H 6S3

Att. : Céline Morin

Electrical Services, Regina, SK

Royal Canadian Mounted Police | Published December 6, 2016  -  Deadline April 1, 2017
cpvs

Trade Agreement: Agreement on Internal Trade

Tendering Procedures: All interested suppliers may submit a bid

Competitive Procurement Strategy: Lowest Compliant Bid

Nature of Requirements: Electrician Services

Work under this Standing Offer will involve, but not be limited to, providing labour, equipment, supervision and materials for the services of an electrician at the RCMP Academy, Depot Division, Regina, Saskatchewan as requested by the Royal Canadian Mounted Police (RCMP) in the form of call ups. Services are to be provided on an “as required basis”. It is anticipated that one firm will be issued a Standing Offer. The Standing Offer will be issued for a period of three (3) years with the option to extend the term of the Standing Offer for one (1) additional one (1) year option period. The total estimated expenditures for the first year is $100,000.00 excluding GST/HST.

RETURN BIDS TO: Bid Receiving Unit

RCMP / GRC

Procurement & Contracting services

c/o Commissionaires, F Division

6101 Dewdney Avenue

Regina, SK S4P 3K7

Security Requirement:

There is a security requirement associated with the requirement.

Evaluation Procedures:

Bids will be assessed in accordance with the entire requirement of the bid solicitation including the financial criteria. An evaluation team composed of representatives of Canada will evaluate the bids.

Basis of Selection:

A bid must comply with all requirements of the bid solicitation to be declared responsive. The responsive bid with the lowest evaluated price will be recommended for award of a contract.

The Crown retains the right to negotiate with suppliers on any procurement.
Documents may be submitted in either official language of Canada.

RCMP has adopted the Integrity Regime administered by PWGSC. As a result, the integrity provisions are being applied in RCMP contracting activities as outlined in this solicitation.

The RCMP has published it’s National Procurement Plan for 2016/17. For further information please see link: http://www.rcmp-grc.gc.ca/en/rcmp-national-procurement-plan

Track Driven Loader

Parks Canada | Published January 24, 2017  -  Deadline June 3, 2017
cpvs

Trade Agreement: NAFTA/AIT/Canada FTAs with Peru/Colombia/Panama Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   Track Driven Loader  5P426-160445/A Jane Ray Telephone No. - (403) 472-1742  Fax No. - (403) 292-5786   Track Driven Loader - Waskesiu Lake, Saskatchewan Canada  For the supply, delivery, off-loading, and warranty of one (1) Bobcat T770 (T4) track driven loader equipped with 60 Forestry Cutter and Heavy Duty Bucket with teeth, for Parks Canada, located in Prince Albert National Park, Waskesiu Lake, Saskatchewan, Canada, in compliance with the minimum mandatory specifications outlined at AnnexA, Requirement.   No Substitute Justification:  The T770 (T4) Bobcat Track Driven Loader is the only product that meets the needs of Parks Canada located in Fort Saskatchewan, Alberta.  The electrical controls of the T770 (T4) Bobcat Track Driven Loader is the only track loader that is compatible with electric/hydraulic implements/attachments already owned. This electrical wiring harness is unique to Bobcat.  See solicitation bid document for full details.  Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

EWIS and APS Trainers

Department of National Defence | Published November 28, 2016  -  Deadline September 1, 2017
cpvs

Trade Agreement: WTO-AGP/NAFTA/AIT/Canada FTAs with Peru/Colombia/Panama Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   EWIS and APS Trainers  W0113-16CS24/A Gao, Feng Telephone No. - (905) 615-2057 (    ) Fax No. - (905) 615-2060 (    )  Canadian Forces School of Aerospace Technology and Engineering (CFSATE), Canadian Forces Base (CFB) Borden, Borden, ON requiresthe supply, delivery and training of five (5) Aircraft Power Systems (APS) Part Task Trainers (PTT) and the supply, delivery and training of eight (8) Electrical Wiring Interconnection System (EWIS) Part Task Trainers (PTTs).   The Aircraft Power Systems (APS) Part Task Trainers (PTT) are required to aid in the instruction of aircraft power systems to Avionics Systems (AVS) Technicians while the Electrical Wiring Interconnection System (EWIS) Part Task Trainers (PTTs) will support Avionics Systems (AVS) Technician students in learning the skills necessary to preform aircraft electrical wire repairs. The EWIS trainer will also provide a platform for students to perform increasingly complex repairs as the course progresses.  The EWIS and APS Trainersmust be delivered by March 27, 2017.  A bid must comply with the requirements of the bid solicitation and meet all mandatory technical evaluation criteria to be declared responsive.  The responsive bid with the lowest price will be recommended for award of a contract. Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

FLYER’S HELMET SPARES

Department of National Defence | Published December 13, 2016  -  Deadline June 1, 2017
cpvs

***** update aricle 2.2*******

NOTICE OF PROPOSED PROCUREMENT- W8485-173848/B

The Department of National Defence has a requirement for the items detailed below. The delivery is requested at plant by soonest date possible.

Item 1, GSIN: N5995, NSN: 5995-21-914-2931, CABLE ASSEMBLY

SPECIAL PURPOSE ELECTRICAL, Part No: U1738402 , NCAGE 38655

 Quantity: 100, Unit of Issue: EA, FCA to 25 CFSD.

Item 2, GSIN: N5995, NSN: 5995-21-879-2852, CORD ASSEMBLY

ELECTRICAL, Part No: UR988401-20 , NCAGE – 38655

Quantity: 50, Unit of Issue: EA, FCA to 25 CFSD

Item 3, GSIN: 5995, NSN: 5995-01-532-1759, WIRING HARNESS,BRANCHED

Part No: CEP900-104, NSCM/CAGE – 1JGL0, Quantity: 200, Unit of Issue: EA,

FCA to 25CFSD

Item 4, GSIN: 5995, NSN: 5995-01-532-1759, WIRING HARNESS,BRANCHED

Part No: CEP900-104, NSCM/CAGE – 1JGL0

Quantity: 100, Unit of Issue: EA, FCA to 7 CFSD

Item 5, GSIN: 5995,NSN: 5995-01-442-8891, CABLE ASSEMBLY,SPECIAL PURPOSE,ELECTRICAL, Part No: 11046D, NCAGE – 18068,

Quantity: 25, Unit of Issue: EA, FCA to 25 CFSD

Item 6, GSIN: 5995,NSN: 5995-00-296-8037, CORD ASSEMBLY,ELECTRICAL BRANCHED, Part No: 7334776-10, NCAGE – 82872

Quantity: 85, Unit of Issue: EA, FCA to 25 CFSD

Item 7, GSIN: 5965,NSN: 5965-01-056-7225, EARPHONE

Part No: M18239-2,NCAGE:81349

Quantity: 250, Unit of Issue: EA, FCA to 25 CFSD

Item 8, GSIN: 5965, NSN: 5965-01-597-2591, CUSHION, EAR
Part No: 28118T NCAGE: OWY76 

Quantity: 200, Unit of Issue: EA, FCA to 25 CFSD

Item 9, GSIN: 5965, NSN: 5965-01-319-5363, ADAPTER, MICROPHONE

Part No: 11194, NCAGE –18068

Quantity: 50, Unit of Issue: EA, FCA to 25 CFSD

Item 10, GSIN: 5965,NSN: 5965-01-341-3837, FILTER,ACOUSTICAL

Part No: 40062G-01, NCAGE – 71483

Quantity: 300, Unit of Issue: EA, FCA to 25 CFSD

Item 11, GSIN: 5965, SN: 5965-01-593-3593 , BINAURAL MINI-CEP

Part No: CEP109-C17 (REV 1), NCAGE –1JGL0

Quantity: 150, Unit of Issue: EA, FCA to 25 CFSD

Item 12, GSIN: 5965, NSN: 5965-01-588-6708,HEADSET-MICROPHONE

GSIN: N5965, NSN:5965-01-588-6708,

Part No: CEP508-C15 NCAGE:1JGLO

Quantity: 150, Unit of Issue: EA, FCA to 25 CFSD

Item 13, Deleted

Item 14, Deleted

Item 15, GSIN: N6230, NSN: 6230-01-357-2174, FLASHLIGHT

Part No: ML-8A , NCAGE: OST81

Quantity: 250, Unit of Issue: EA, FCA to 25 CFSD

Item 16, GSIN: N6230, NSN: 6230-01-534-2760, FLASHLIGHT

Part No: ML-24, NCAGE: OST81 

Quantity: 250, Unit of Issue: EA, FCA to 25 CFSD

Item 17, GSIN: N6230, NSN: 6230-01-601-4299, LIGHT HEAD,UTILITY
Part No: HS-403 , NCAGE: 42AQ2 

Quantity: 25, Unit of Issue: EA, FCA to 25 CFSD

Item 18, GSIN: N6230, NSN: 6230-14-584-3206, LIGHT HEAD ,UTILITY

Part No: E93HN, NCAGE: F8695 

Quantity: 350, Unit of Issue: EA, FCA to 25 CFSD

Add Item 19, GSIN: NSN 5965-01-523-3153, HEADSET,ELECTRICAL

Part No: CEP402-C05,NCAGE: 1JGLO

Quantity: 250, Unit of Issue: EA, FCA to 25 CFSD

Add Item 20, GSIN: NSN 5965-01-518-0623, HEADSET ELECTRICAL

Part No: CEP508-K04-R1,NCAGE: 1JGLO

Quantity: 150, Unit of Issue: EA, FCA to 25 CFSD

Bidders proposing an Equivalent or a Substitute Product must indicate the brand name and model and/or Part Number and the NCAGE they are offering.

The Crown retains the rights to negotiate with suppliers on any

Washers and Dryers

Department of National Defence | Published January 31, 2017  -  Deadline March 13, 2017
cpvs

Trade Agreement: NAFTA/AIT/Canada FTAs with Peru/Colombia/Panama Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   Washers and Dryers  W0125-17CR05/B Braganza-Reyes, Caroline Telephone No. - (905) 615-2397 (    ) Fax No. - (905) 615-2060 (    )  The Department of National Defence has a requirement for the supply and delivery of 48 washing machines and 48 dryers for a total of 96 appliances to be delivered on or before March 30, 2017.   The proposed bidder must meet all mandatory criteria detailed in the Request for Proposal document.  Some of the minimum specifications are outlined below.  See the full RFP for all mandatory criteria.   A. Washing Machine i. CSA approval ii. 110  120 Volts  iii. Electrical cord must be attached iv. Extra-large capacity 4.2 Cu. Ft. v. 2 water inlets: one cold water and one hot water vi. Top load vii. Stainless steelwash basket viii. Must have a power wash and power wash agitator to better remove stains. ix. Exterior colour must be white   B. Electric Dryer i. CSA approval ii. 220  240 Volts iii. Electrical cord must be attached iv. Extra-large capacity 7.0 Cu. Ft. v. Front load vi. Sensor which stops dryer when cloths are dry vii. Wrinkle control option or equivalent viii. Sanitize cycle ix. Exterior colour must be white Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

Shore Power Modifications, Saint John Ferry Terminal, Saint John, N.B.

Public Works and Government Services Canada | Published February 3, 2017
cpvs

Trade Agreement: Agreement on Internal Trade (AIT) Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   EB144-172812/A Doucet, Gisele PWB Telephone No. - (506) 636-4541  Fax No. - (506) 636-4376   Shore Power Modifications, Saint John Ferry Terminal, Saint John, New Brunswick  Public Works and Government Services Canada has a requirement for electrical remediation of the structure at the Saint John Ferry Terminal, Saint John, N.B.  The work consists of, but is not necessarily limited to, the following: 1) Removal and disposal of existing electrical equipment; 2) Installation of new electrical equipment, re-feeding existing equipment, conduit, wire and associated work; 3) New ventilation system; and 4) All other materials.All work is to be performed in accordance with the plans and specifications for PWGSC Project Number R.074250.001 forming part of the bid document.  Contract completion is to bewithin fifty-two (52) weeks after contract award.  There will be an optional site visit on February 14, 2017 at 14:30 hours.  All interested bidders are to meet at the Saint John Ferry Terminal Wharf, Saint John, N.B.  Although not mandatory, all contractors wishing to submit a tender for this work are encouraged to attend to become familiar with all aspects of the work.  It is recommended that the Bidder or a representative of the Bidder visit the worksite and examine the Scope of the Work required and the existing conditions.  Any clarifications or changes to the bid solicitation resulting from the site visit will be included as an amendment to the bid solicitation.  Please note that this will be the only site visit for this project.  No other site visits will be arranged during the tender period.  New measures related to Integrity provisions included in the solicitation documents requires attention.  The estimated cost for this opportunityis within the following cost category: $250,001.00 - $500,000.00 (HST included). Standard bid and contract security for the construction is required.  A public bid opening will be held at the Bid Receiving Unit, Room 405, 189 Prince William Street, Saint John,N.B.  Inquiries: All inquiries of a technical nature and all questions of a contractual nature are to be submitted in writing to the Contractual Authority: Gisele Doucet, telephone- (506) 636-4541, facsimile - (506) 636-4376 e-mail - gisele.doucet@pwgsc.gc.ca. Inquiries are to be made in writing and should be received no less than five (5) calendar days prior to the closing date to allow sufficient time to respond.  Inquiries are to be made in accordance with SI03  Enquiries During The Solicitation Period, under Special Instructions To Bidders inthe solicitation document.  Firm intending to submit tenders on this project should obtain tender documents through the Government Electronic Tendering System (GETS).  Addenda, when issued, will be available on GETS..  Standard terms and conditions for this procurement are incorporated by reference, and form part of the tender and contract documents.  The standard documents are issued by Public Works and Government Services and may be viewed at buyandsell.gc.ca.  This PWGSC office provided procurement services to the public in both official languages.  The Crown retains theright to negotiate with suppliers on any procurement.  Documents may be submitted ineither official language of Canada. Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

Structural Modifications to the Bay Bulls Warehouse

Fisheries and Oceans Canada | Published January 20, 2017  -  Deadline September 2, 2017
cpvs

Located at the DFO Small Craft Harbours facility in Bay Bulls, NL, the Bay Bulls Warehouse provides operational storage capacity for DFO Fisheries Management (Conservation and Protection Directorate). The existing warehouse consists of an insulated wood frame structure with approximate dimensions of 12.5m x 12.5m, with a concrete perimeter frost wall and concrete floor slab.

DFO require an extension to the existing warehouse to increase storage capacity. As such, a Contractor is required to supply and install all construction materials, labour, consumables and equipment to complete a lean-to style extension to the existing warehouse of approximate 3.0m x 8.5m. Complete details of the scope of work are found in the Technical Specifications and Drawings provided, with a brief summary by discipline provided below:

1. Civil – Earthworks required to prepare ground for placement of frost wall foundation extension and concrete floor slab.

2. Structural – Placement of frost wall foundation extension and floor slab, and installation of timber wall and roof framing.

3. Architectural – Sheathing of building (interior and exterior), installation of siding, fascia, soffit, roof shingles, sealing of all penetrations.

4.  Electrical – Installation of new interior lighting (fed from the existing electrical breaker panel in the warehouse).

The following have been identified as key issues that will need to be considered during the execution of this project:

- All temporary supports required to complete the warehouse extension are the responsibility of the Contractor. The Contractor is to supply a detailed plan of the temporary supports for approval by the Owner’s representative prior to installation.

- The area at the rear of the building will be cleared of storage materials prior to the start of the project. However, the Contractor is responsible for ensuring that the items remaining in the Warehouse that are owned by DFO are secured and protected from the elements for the duration of the project.

- Any hoarding, temporary barriers, signage, and security measures are the responsibility of the Contractor for the duration of the project.

- This work is targeted to be completed during the 2017 winter season. All heating equipment and materials required to achieve proper ground preparation and to allow for the placement of concrete is the responsibility of the Contractor.

Site Visit:

A non-mandatory site viewing will be scheduled for Thursday, January 26th, 2017 at 11am. Contractors wishing to visit the site must contact the Contracting Authority via email to confirm attendance and obtain further information/schedule.

Before submitting a bid, bidders can visit the site and its surroundings, at their own expense, to review and verify the form, nature, and extent of the work, materials needed for the completion of the work, the means of access to the site, severity, exposure, and uncertainty of weather, soil conditions, any accommodations they may require, and in general shall obtain all necessary information as to risks, contingencies, and other circumstances which may influence or affect their bid. No allowance shall be made subsequently in this connection on account or error or negligence to properly observe and determine the conditions that will apply.

Craning, handling and transportation of Rideau Canal Skateway (RCS) Chalets and trailers

National Capital Commission | Published February 24, 2017  -  Deadline May 4, 2017
cpvs

General Description:

Each year, 7 Skateway chalets, 2 service trailers and an electrical kiosk need to be craned in/out of the Rideau Canal. The chalets and trailers are installed at four locations on permanent, or none permanent pillars along the Skateway. See Appendix 1 – Rideau Canal Map Book for the exact locations of the chalets and trailers. Both trailers are installed at the Fifth Ave rest area, one trailer (40ft) is shown on the plan as the Skateway first aid trailer and the second trailer (32ft) is shown as the washroom. See Appendix 2 for pictures of trailers and electrical kiosk specifications. The NCC is, looking for a proponent for the coordination of “turnkey” service for the craning (using a crane with appropriate reach radius and weight capacity), the handling (from cribbing at warehouse to pillars on the canal) and the transportation to and from our Woodroffe warehouse to its final position. The supplier must consider that the removal phase includes all the steps mentioned for the installation. See Appendix 3 – for typical timeline of operations

The Chalets will be transported by a uniform handling system. The basis of the handling will be that the chalets will be carried by the (2) two main structural frame beams, or suspended by the designed lifting eyes to avoid any stress or torsion on the chalets structural frames. This custom uniform single point of movement control system, a trailer, or any carrying system has to have the ability to be positioned between the support blocking (that is supporting the chalets). The transportation system will have to transfer the load ( the Chalets), (by means of hydraulics or air suspension ) to the mobile system ( trailer or “dolly” system ) complete with designed supports, which will be positioned under the chalets two (2) main structural frame beams. (Contact points complete with “hold-downs”).

For the installation, the Chalet units will be off loaded and placed on the fixed pillars, located for support in the canal, by crane.

For the removal, the units will be placed on the custom system by crane and transported to a designated storage area. The units will be positioned between blocking, raised by the carrying system, blocking placed, lowered on to the structural beams, and the system pulled out from under.

For the two (2) trailers, the lifting frame cannot be used to crane it on and off the canal. For the procedure, (2) two main structural frame beams will need to be positioned under the trailer frames. 

The official Government Electronic Tendering Service website is http://buyandsell.gc.ca . Please ensure that you download your document from this site, in order to obtain all information related to the tender. It is your responsibility to ensure that you have received all the posted tender information to ensure tender compliance and not be disqualified.
Tenders & bid security must be forwarded to the attention

Procurement Services

National Capital Commission

40 Elgin Street

2nd Floor Security Office

Ottawa, ON K1P 1C7

Envelope to reference NCC tender file # AL1691.

Bid closing date is April 5, 2017 at 3pm EDT. Late or faxed bids will not be accepted.
There is a public opening scheduled shortly after the bid closing time in room 306 at 40 Elgin Street, 3rd floor, Ottawa, ON.
The procurement process of this tender is subject to WTO - Agreement on Government Procurement.

MCCP Retrofit, Building 5, Dorchester Penitentiary, Dorchester, NB

Public Works and Government Services Canada | Published February 24, 2017
cpvs

Trade Agreement: Agreement on Internal Trade (AIT) Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   EC016-172885/A MacDonald, Anne (PWC) D. Telephone No. - (902) 626-4949 (    ) Fax No. - (902) 566-7514 E-mail:  anne.macdonald@pwgsc.gc.ca  MCCP Retrofit, Building 5, Dorchester Penitentiary  Medium Security, Dorchester, NB  In general, work under this contract consists of but not limited to:  1. Selective demolition of architectural, mechanical and electrical systems. 2. Supply and installation of HVAC, plumbing systems and electrical work. 3. Supply and installation of two exterior windows including painting & ceiling system replacement.   Infill of one exterior window with masonry. 4. Supply and installation of finish work.  i.e. patching, painting, flooring, etc.  The site of the work is Building B-5, first level, Dorechester Penitentiary, Medium sector, 4902 Main Street, Dorchester, New Brunswick E4K 2Y9  There will be a site visit on March 16, 2017 at 11:00 AM. Interested bidders are to meet at the principal entrance, Dorchester Penitentiary, 4902 Main Street, Dorchester, New Brunswick.  There is a security clearance required to attend this site visit. ALL interested bidders, regardless of current clearance level, must submit the Institutional Access CPIC Clearance request form located in Annex D of this solicitation document. With the CPIC, bidders must also provide a copy of an official form of photo identification such as a drivers license or passport. These must submitted to Anne MacDonald by fax at (902) 566-7514 or e-mail anne.macdonald@pwgsc- tpsgc.gc.ca by 16:00 hours, March 1, 2017. No cameras will be allowed on the site.  All work is to be performed in accordance with the plans and specifications for Project Number R.080786.001 forming part of the bid document  The estimate for this opportunity is within the following cost category:  $250,001 - $500,000.  The Contractor shall perform and complete the Work by July 31, 2017.   New measures related to Code of Conduct and certifications included in the solicitation documents requires attention.   Inquiries: All inquiries of a technical nature and all questions of a contractual nature are to be submitted in writing to the Contractual Authority: Anne MacDonald, telephone - (902)626-4949, facsimile - (506) 636-4376, e-mail - anne.macdonald@pwgsc.gc.ca. Inquiries are to be made in writing and should be received no less than five (5) calendar days prior to the closing date to allow sufficient time to respond.  Inquiries are to be made in accordance with SI03 - Enquiries During The Solicitation Period, underSpecial Instructions To Bidders in the solicitation document.  Standard bid and contract security for construction is required.   Firms intending to submit tenders on this project should obtain tender documents through the Government Electronic Tendering System (GETS). Addenda, when issued, will be available on GETS.   Standard terms and conditions for this procurement are incorporated by reference, and form part of the tender and contract documents. The standard documents are issued by Public Works and Government Services and may be viewed at buyandsell.gc.ca.   This PWGSC office provided procurement services to the public in both official languages.   Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.    Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

RISO-General Maint. Services - BIO

Public Works and Government Services Canada | Published January 31, 2017
cpvs

Trade Agreement: WTO-AGP/NAFTA/AIT/Canada FTAs with Peru/Colombia/Panama Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   RISO-General Maint. Services - BIO  E0225-170039/A Matheson, Valerie Telephone No. - (902) 496-5100 (    ) Fax No. - (902) 496-5016 (    )  GSIN:  5129B  Trade Agreement:  WTO-AGP/NAFTA/AIT/Canada FTAs with Peru/Colombia/Panama Tendering Procedures:  All interested suppliers may submit a bid Competitive Procurement Strategy:  Lowest/Lower Bid Comprehensive Land Claim Agreement:  No  Public Services and Procurement Canada on behalf of the Department of Fisheries and Oceans has a requirement for a Regional Individual Standing Offer for provisions of all labour, material, tools, test equipment and equipment necessary to perform minor construction and/or minor repairs and maintenance to buildings and building eqipment, including strucural, electrical, mechanical and painting at the following locations:  Bedford Institute of Oceanography, Traffic Centre, Dartmouth and Coast Guard Hangar, Shearwater.  This requirement is on an "as" and "when" requested basis.  The period of the Regional Individual Standing Offer will be for a one year period beginning on April 1, 2017 with the option to extend up to two additional one year periods if required.  SECURITY In order to be awarded a contract which contains a security requirement, all biddersMUST hold a valid Security Clearance granted or approved by PSPC Canadian Industrial Security Directorate (CISD) at the level indicated in this Solicitation document.  INQUIRIES All inquiries of a technical nature and all questions of a contractual nature are to submitted to the Contracting Authority:  Valerie Matheson, valerie.matheson@pwgsc.gc.ca, facsimile:  (902) 496-5016.  Inquiries are to be made in writing and should be received no less than five (5) calendar days prior to the closing date toallow sufficient time to respond.  Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

Technical Investigation and Engineering Support (TIES) for the Canadian Coast Guard (CCG)

Fisheries and Oceans Canada | Published February 7, 2017  -  Deadline July 3, 2017
cpvs

Trade Agreement: Agreement on Internal Trade (AIT) Tendering Procedures: The bidder must supply Canadian goods and/or services Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   Technical Investigation and Engineering Support (TIES) for the Canadian Coast Guard (CCG)  F7048-090005/H Figueredo, Laila Telephone No. - (819) 420-2904  Fax No. - (819) 956-0897   OPPORTUNITY FOR ADDITION, UPDATE, AND QUALIFICATION  This process provides for existing suppliers to add areas of expertise and update their list of personnel and subcontractors; and new suppliers with an opportunity to qualify for a supply arrangement.  The Supplier will provide Technical Investigation and Engineering Support (TIES) for the Integrated Technical Services Directorate of the Department of Fisheries and Oceans, Canadian Coast Guard (CCG) located within the following regions: National Capital Region, Western, Central & Arctic, and Atlantic, excluding locations within Comprehensive Land Claims Settlement Areas.  The period for awarding contracts under the Supply Arrangement is from the date of the supply arrangement to 31 March 2018, with an option to extend by one (1) additional period of two (2)years.  The requirement is subject to the provisions of the Agreement on Internal Trade (AIT).  The requirement covered by the bid solicitation of any resulting supply arrangement is solely limited to Canadian services.  The Request for Supply Arrangement evaluation process will qualify suppliers by area of expertise.  To receive a supply arrangement, the supplier must meet the mandatory requirements and achieve the minimum scores in at least two (2) of the following areas of expertise:  A. Naval Architecture B. Marine Engineering C. Hovercraft Systems D. Marine Communication and Navigation Systems: Vessel Based E. Marine Communication and Navigation Systems: Shored Based F. Marine Informatics Technology G. Infrastructure H. Mechanical, Electrical & Power Systems: Shored Based I.  Aids to Navigation J. Environmental Services: Vessel and Shore Based K. Health and Safety Services L. Integrated Logistics Support   Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

16-1313 - Interior Fit-Up/Renovations CEF Building 55

Agriculture and Agri-Food Canada | Published December 13, 2016  -  Deadline May 1, 2017
cpvs

Delivery Date:
The work shall commence immediately upon official notification of acceptance of tender by the Contracting Authority and is to be completed by February 28th, 2017.

Mandatory Site Visit Date:
A site visit has been scheduled for December 20, 2016 @ 10:00 AM EST. Bidders are to meet in the Main Lobby of Building 55, 960 Carling Ave. Ottawa, ON K1A 0C6. Please see the Central Experimental Farm building area map

Bids submitted by Bidders who do not attend the Site Visit will not be accepted.

Bid Close:
Bids must be submitted in a sealed envelope before the bid closetime of Thursday January 5, 2016 @ 2:00 PM EST. Bids must be submitted to the Main Lobby of the K.W. Neatby Building 960 Carling Ave. Ottawa, ON K1A 0C6.

Firms intending to submit tenders on this project should obtain tender (solicitation) documents through GETS - buyandsell.gc.ca. Addenda, when issued will be available from GETS - buyandsell.gc.ca. Firms that elect to base their bids on tender (solicitation) documents obtained from other sources do so at their own risk. In all cases, bidders must indicate (when requested) in the space provided on the tender form the identificationnumber (s) of the addenda, if any, that they have taken into consideration for their bid.

The documents (Invitation to Tender, Electrical and Mechanical drawings) are available as attachments below.

Documents may be submitted in either official language of Canada.

Rental of Generators/Heaters/Lights

Department of National Defence | Published December 1, 2016  -  Deadline November 1, 2017
cpvs

Trade Agreement: WTO-AGP/NAFTA/AIT/Canada FTAs with Peru/Colombia/Panama Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   This request for standing offers (RFSO) cancels and supersedes previous RFSO number W0106-15B008/A dated September 1st 2016 with a closing date of October 12th at 14:00 Eastern Daylight Time (EDT)  RISO Rental of Generators, Heaters and Light tower Kits GSIN: WR6115  Generators and generator sets, electrical - rental   Request for a Regional Individual Standing Offer (RISO) for the rental upon request of construction equipment such as generators, heaters and light tower kits for the Department ofNational Defense (DND) located in Quebec, Montreal et à Saint-Jean-sur-Richelieu, Quebec, as described in Annex «A».  The resulting Standing Offer will be valid for a period of two (2) years from the date that the SO is issued and will include a rightfor Canada to authorize an additional period of one year.  The requirement is subject to the provisions of the World Trade Organization Agreement on Government Procurement (WTO-AGP), the NorthAmerican Free Trade Agreement (NAFTA), and the Agreement on Internal Trade (AIT) as well as the Free Trade Agreement with Free Trade Agreement with Columbia, the Free Trade Agreement with Panama and the Free Trade Agreement with Peru.  The supplier will beselected following an evaluation based on mandatory technical criteria and financial evaluation criteria.  All inquiries and other communications concerning this Request for Standing Offer must be sent in writing only to the contracting authority named in the Request for Standing Offer.     Public Worksand Government Services Canada provides services in Canada's two official languages.  Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

AAFC Lacombe Facility System Renovation, Lacombe, AB

Public Works and Government Services Canada | Published January 6, 2017  -  Deadline July 2, 2017
cpvs

Trade Agreement: Agreement on Internal Trade (AIT) Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   This bid solicitation cancels and supersedes previous bid solicitation number EP922-172162/A dated November 28, 2016 with a closing of December 14, 2016 at 02:00 PM MST.  AAFC Lacombe Research Facility Renovation, Lacombe, AB  Public Works and Government Services Canada on behalf of Agriculture and Agri Food Canada requires contractor services for the Lacombe research facility renovation, Lacombe, Alberta.   Work for Contract comprises the provision of new water treatment, heat exchangers, pumps,make-up air unit, exhaust fan, new electrical panel in the existing mechanical room.  OPTIONAL SITE VISIT There will be a site visit on January 26, 2017 at 10:30 AM.  Interested bidders are to meet at the Lacombe Research Centre, 6000 C&E Trail, Lacombe, Alberta.   VALUE OF PROJECT: To assist with bonding and insurance requirements, this project is estimated at a value between: Category 2          $100,001> $ 250,000  This PWGSC Office provides procurement services to the Public in English.  The Crown retains the right to negotiate with suppliers on any procurement.  Email  mony.lee@pwgsc-tpsgc.gc.ca   IMPORTANT NOTICE TO BIDDERS  Notifications about amendments to an opportunity:  Buyandsell.gc.ca/tenders provides a Web feed to keep you informed about amendments to an opportunity of interest.  Firms intending to submit bids on this project should obtain bid documents through the GETS service provider on the Government of Canada Web site at http://buyandsell.gc.ca/procurement-data/tenders. Firms that obtain bid documents from a source other than the official site run the risk of not receiving a complete package.    Delivery Date: Above-mentioned  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.

Building Construction at 441 University Ave

Public Works and Government Services Canada | Published February 27, 2017  -  Deadline November 4, 2017
cpvs

Trade Agreement: WTO-AGP/NAFTA/Canada FTAs with Peru/Colombia/Panama Tendering Procedures: All interested suppliers may submit a bid Competitive Procurement Strategy:  Comprehensive Land Claim Agreement: No Nature of Requirements:   Building Construction at 441 University Ave  EQ754-172715/A Dhillon, Ambreen Telephone No. - (416) 590-8253 (    ) Fax No. - (416) 512-5862 (    )  Public Works and Government Services Canada (PWGSC) has a requirement for a qualified general contractor for the renovation and fit-up of 441 University Ave. in Windsor ON.  Project No.  R.012641.001  SCOPE OF WORK: The Work includes but is not limited to the  exterior and interior renovation of the existing Government of Canada Building at 441 University Avenue West, Windsor, Ontario N9A 5P9. Work will include but is not limited to: .1 Demolition of interior walls, ceilings and finishes and Hazardous Materials Remediation .2 Exterior masonry repair and cladding, door, window and roof replacement, HVAC, sprinkler, electrical, communication and life safety system upgrades, elevator modernization, new interior walls and finishes, exterior works including parking and landscaping, and new rooftop photovoltaic system.  Mandatory Site Visit:  There will be a site visit on March 21, 2017 at 10:00am. Interested Bidders are to meet at the principal entrance of existing Government of Canada Building at 441 University Avenue West, Windsor, Ontario N9A 5P9.  The site visit for this project isMANDATORY.  The representative of the bidder will be required to sign the Site Visit Attendance Sheet at the site visit. Bids submitted by Bidders who have not signed the attendance sheet will not be accepted.  Personal Protection Requirements: Visitors should  wear safety boots and a hard hat  All enquiries of a technical and contractual nature, are to be submitted to the Contracting Officer, Ambreen Dhillon:  e-mail:  ambreen.dhillon@pwgsc.gc.ca Telephone: (416) 590-8253,  or  Facsimile:  (416) 512-5862.  Bid Receiving:    Sealed tenders will be received at Public Works and Government Services Canada, 4900 Yonge Street, Bid Receiving, 12th Floor, Toronto,Ontario M2N 6A6.   Delivery Date: 24/02/2017  The Crown retains the right to negotiate with suppliers on any procurement.  Documents may be submitted in either official language of Canada.